Na czym polega modelowanie hydrologiczne, czyli zastosowanie nowoczesnych metod obliczeniowych do odwzorowania lokalnych i regionalnych systemów obiegu wody? I jakie korzyści przynosi?
“Mineral deposit model”, “deposit modelling” are the terms commonly used, although imprecise. This is often identified as the application of computerized methods to the elaboration and presentation of geological information, in particular for the mining design. Deposit modelling is the mode of presentation of deposit features, which in the meaning of the authors of such presentation, describes the deposit features between the points of observations as best as possible. Deposit modelling has a long history (XVI-XVII centuries), however such a term was not used. Varied methods of cartographic presentation of deposits and their features were proposed. The progress in the presentation of the deposit in space using isolines maps has led to the separation of methods of deposits geometrisation. Over time, a simple mathematical statistics method was used to describe the deposit parameters, followed by geostatistical methods. Some of them were however not commonly used as too troublesome. The computer based approach to the presentation of geological data has an unquestionable value but is accompanied by the possibility of inappropriate formalized and erroneous interpretations and a presentation as to whether the basic rules of geological knowledge were neglected. Deposits modeling is a conceptual task and cannot be fully automated.
O tym, czym jest modelowanie i na czym polega modelowanie pracy mózgu, rozmawiamy z prof. Danielem Wójcikiem z Instytutu Biologii Doświadczalnej im. Marcelego Nenckiego PAN.
Computational modeling plays an important role in the methodology of contemporary science. The epistemological role of modeling and simulations leads to questions about a possible use of this method in philosophy. Attempts to use some mathematical tools to formulate philosophical concepts trace back to Spinoza and Newton. Newtonian natural philosophy became an example of successful use of mathematical thinking to describe the fundamental level of nature. Newton’s approach has initiated a new scientific field of research in physics and at the same time his system has become a source of new philosophical considerations about physical reality. According to Michael Heller, some physical theories may be treated as the formalizations of philosophical conceptions. Computational modeling may be an extension of this idea; this is what I would like to present in the article. I also consider computational modeling in philosophy as a source of new philosophical metaphors; this idea has been proposed in David J. Bolter’s conception of defining technology. The consideration leads to the following conclusion: In the methodology of philosophy significant changes have been taking place; the new approach do not make traditional methods obsolete, it is rather a new analytical tools for philosophy and a source of inspiring metaphors.
The complexity of the phenomena associated with the course of the cognitive processes that determine an efficient learning, excludes the possibility of collecting knowledge in other ways than neuronal-information. It excludes also possibilities of interpreting it, in other ways than with use of respectively formalized cognitive models. The presented paper is a kind of summary of the latest achievements in this field.
Safe mine operations and optimal economical decision making in the context of lignite resources require an adequate level of knowledge about the spatial distribution of critical attributes in terms of geometry and quality in the deposit. Therefore, ore body models are generated using different approaches in geostatistics, depending on the problem to be solved. In this article the analysis of geostatistical methods used for deposits modeling has been presented. Based on exploration data concerning caloric value Q, models of one exemplary lignite deposit has been made. Two models of deposit were prepared using two different methods: ordinary kriging (OK) and sequential Gaussian conditional simulation (SGSIM). Different models of the same deposit were analyzed and compared with source data using criterion of fidelity to statistical attributes like: mean value, variance, statistical distribution. Models, which have been created based on exploration data, were compared with in-situ data gained from survey activities in the exploitation process. As a result of comparison correlation factor and measures of deviations were computed: average relative error, absolute relative error. Models were compared with in situ data, considering statistical features and local variability as well. In conclusion, the study gives valuable information into the benefits of using certain geostatistical approaches for variable tasks and problems in the lignite deposits design process. For the assessment of average values of deposit parameters ordinary kriging provides appropriate effects. Geostatisical simulation (e.g. sequential Gaussian simulation - SGSIM) provides much more relevant information for tasks connected to probability (or risk) of defined threshold exceedences than ordinary kriging. Models made with simulation method are characterized by high fidelity of spatial distribution in comparison to source data.
Prognozowanie pogody wymaga znajomości praw rządzących ruchem atmosfery. Obok mechaniki płynów trzeba uwzględnić ruch obrotowy naszej planety, zróżnicowane nagrzewanie jej powierzchni wskutek pochłaniania promieniowania słonecznego, a także procesy parowania wody i kondensacji pary wodnej.
Two formal types of models of living processes, especially evolutionary ones, may be distinguished: the well-known mathematical type and the less-known logical one. The latter applies the terms “class” or “set”; both the terms are understood either in a collective sense (in mereology) or in a distributive sense (in set theory). These formal terms may be used among others to such organic multiplicities as populations or species of organisms, and to organic constituents (molecules, cells, organs) of living organism. Collective concepts refer to objects existing in nature, whereas distributive concepts refer to the linguistic and research constructions of models of natural objects, developed to cognitively grasp natural regularities.
The operational mineral deposit reconnaissance tends to evaluate its parameters to conduct safe and profitable production. Particular deposit parameters, important from the point of mineral deposit management, are estimated on the basis of observations carried out by mining geological surveys. These observations usually involve sampling, drilling, laboratory analyses and others. The use of fuzzy description to assess the parameters of the mineral deposit was proposed in the paper. In the fuzzy characteristics, an imprecise descriptive description appeared in place of a particular numerical quantity. This approach was used to description of the ore deposit features (metal content, volume, and metal yield) by assigning them specific characteristic functions, whose distributions were based on basic statistical quantities. Characteristic functions can be used to prepare operational strategies for any configuration of required deposit parameters resulting from the production management needs. For this purpose, selected logical operators of fuzzy sets were used. In the next approach to fuzzy modeling, an opportunity to characterize the deposit in a subjective approach was indicated, where the assessment of the deposit parameters is based on rough, in some way, discretionary observation and evaluation. Such model construction enabled the overall assessment of the deposit from the point of view of any parameters. Through the implementation of appropriate inference rules, adequate fuzzy control planes were obtained, which may also be useful in the context of operational mine strategy planning.
Hydrocarbon production under certain geological conditions of these deposits can cause surface subsidence and deformation of the terrain surface. Such deformations appear as subsidence troughs of considerable range and the magnitude of the subsidence depending on the total thickness of the reservoir, compaction properties of reservoir and on the number of other factors. In the past there have been widely recognized magnitudes of the subsidence up to 9 meters. The stress zones in the subsidence trough may affect the buildings and surface structures. However there have been well known some cases of destroyed boreholes or pipelines belonging to the gas or oil mine. Therefore there is a requirement to analyze the possibility of occurrence unfavorable phenomenon on the ground surface, to monitor surface deformations during production and to protect surface infrastructure located in the range of mining influences. In the paper the issue of surface subsidence caused by hydrocarbon production has been presented. The cause - effect relationship between the compaction of thereservoir rock and the subsidence of surface area has been assumed. The prediction model base on the influence function and on the superposition of elementary influences. For the purpose of building damage protection a new model of risk assessment has been developed. This model base on the elements of fuzzy logicallows to incorporate in the analysis the quantitative and qualitative factors that contribute to the risk of building damage. Use of the fuzzy logic made it possible to obtain one value which clearly discriminate the risk of buildings damage. However, risk analyzes of damage to the large number of buildings has been required additional tools. The spatial analysis has been made by using GIS. The subjects of the paper have been illustrated with a practical example.
Najnowsze metody badań, takie jak rentgenowska tomografia komputerowa, są pomocne w poszukiwaniach złóż ropy naftowej i gazu ziemnego. A zastosowanie nowoczesnych metod obliczeniowych pozwala określić rodzaj złoża oraz jego zasobność.
The paper presents results of numerical calculations of a diaphragm wall model executed in Poznań clay formation. Two selected FEM codes were applied, Plaxis and Abaqus. Geological description of Poznań clay formation in Poland as well as geotechnical conditions on construction site in Warsaw city area were presented. The constitutive models of clay implemented both in Plaxis and Abaqus were discussed. The parameters of the Poznań clay constitutive models were assumed based on authors’ experimental tests. The results of numerical analysis were compared taking into account the measured values of horizontal displacements.
The steel pipe umbrella is a widely used technology when tunnelling in weak soils in order to create pre-support ahead of the tunnel face. The design of steel pipes is frequently done through simplified analytical approaches which are easy to apply but require proper assessment of the loads acting on the pipe. To provide information on this key design aspect, the results of the comparison between a three-dimensional numerical model developed with the code FLAC 3D and an analytical model based on the approach of a beam on yielding supports is presented and discussed. The comparison refers to a shallow tunnel with an overburden of three times its diameter for two different types of weak rock masses. The obtained results provide suggestions about the load that has to be applied in the analytical model for the design phase.
This paper presents the analysis of the influence of works related to the dynamic replacement column formation on the bridge pillar and the highway embankment located nearby. Thanks to DR columns, it is possible to strengthen the soil under road embankment in a very efficient way. However, the construction of such support carries risk to buildings and engineering structures located in the neighbourhood. Therefore modelling and monitoring of the influence of the conducted works should be an indispensable element of each investment in which dynamic replacement method is applied. The presented issue is illustrated by the example of soil strengthening with DR columns constructed under road embankment of DTŚ highway located in Gliwice. During the inspection, the influence of vibrations on the nearby bridge pillar and road embankment was examined. The acceleration values obtained during these tests were used to verify the elaborated numerical model.
Complex circuit of milling-classify systems are used in different branches of industry, because the required particle size distribution of product can seldom be reached in a single-stage grinding on the same device. The multistage processes of comminution and classification make possible suitable selection of parameters process for variables graining of fed material, mainly through sectioning of devices or change of their size and the types. Grinding material usually contains size fractions, which meet the requirements relating finished product. Then profitable is preliminary distributing material on a few size fractions, so to deal out with them demanded fraction of product, whereas remaining to direct alone or together with fed material to the same or different device. If the number of mills and classifiers in a circuit is large enough, building the model of particle size distribution transformation becomes rather complicated even for the circuit of a given structure. The situation becomes much more complicated, if we want to compare characteristics of all possible circuits, that can be constructed from these mills and classifiers, because the number of possible circuits increases greatly with the increase of number of devices being in the milling-classify system. The method creating matrix model for transformation of particle size distribution in a circuit of arbitrary structure of milling-classify system is presented in the article. The proposed model contains the mass population balance of particle equation, in which are block matrices: the matrix of circuit M, the matrix of inputs F and the matrix of feed F0. The matrix M contains blocks with the transition matrix P, the classification matrix C, the identity matrix I and the zero matrix 0 or elements describing the transformation of particle size distribution in the circuit. The matrix F is the block column matrix, which elements describing all particle size distributions at inputs to the circuit elements. The matrix F0 is the block column matrix, which elements describing particle size distributions in all feeds to the circuit. In paper was discussed this model in details, showed algorithm and three examples formatrix construction for the closed circuit ofmilling-classify systems. In conclusion was affirmed, that presented model makes possible to forecasting particle size distribution of grinding product, which leaving chosen the unit of system. The matrix model can be applied to improving modeling of mineral processing in the different grinding devices.
The industrial grinding devices, which work in the high-energetic fluidized bed conditions make it possible to obtain guaranteed particle size distribution of product and decrease of consumption energy. The matrix model for transformation of particle size distribution in the fluidized bed opposed jet mill is presented in the part IV of article. The proposed model contains the mass population balance of particle equation, in which are block matrices: the matrix of circuit M, the matrix of inputs F and the matrix of feed F0. The matrix M contains blocks with the transition matrix P, the classification matrix C, the identity matrix I and the zero matrix 0. The matrix was marked using with discrete forms of the selection and breakage functions, mean while the matrices of classification - using the equation, describing classification of grains in the grinding chamber of mill. In paper was discussed this model in details (part 2.1). The correctness of received form of the selection and breakage functions was confirmed. The method determination of the transition matrix for fluidized-jet grinding of grains (part 2.2) and the classification matrix for gravitational and centrifugal zones of grains (part 2.3) are presented. The verification of model obtained on basis results with experimental investigations, which were performed on a laboratory fluidized bed opposed jet mill. The experiment contained grinding of selected narrow size fractions of limestone in turbulent fluidized layer conditions, what in part I and part II of article (Zbroński, Górecka-Zbrońska 2007a, b) are presented. The parameters of parametric identification were: factor of proportionality - contained in the equation on the discrete form of selection function and sizes of limiting grains - contained in equation on the diagonal elements of classification matrix for stage of gravitational and centrifugal (part 3). The classic Fisher-Snedecor test was applied for estimation of prediction particle size distribution of grinding product (part 4). The significant divergences between numerical and experimental results of particle size distribution weren't affirmed. The experimental verification, parametric identification and statistical estimation of the proposed model showed that this model make it possible to forecasting particle size distribution of grinding product.
In recent years adverse processes of suburbanization have been observed in cities. It has become a serious challenge for urban and transport planners, as it influences largely the quality of space, the quality of life, and the cost of running the city. This paper is dedicated to travel models in areas serviced by a railway system, and is based on a real-life survey example of the Błonie community, a district belonging to the Warsaw metropolitan area. Research carried out in 2014 focused on combined travels behaviors recorded using GPS locators as well as quantitative research (volumes of users across various transport systems).
Assessment of the flexural buckling resistance of bisymmetrical I-section beam-columns using FEM is widely discussed in the paper with regard to their imperfect model. The concept of equivalent geometric imperfections is applied in compliance with the so-called Eurocode’s general method. Various imperfection profiles are considered. The global effect of imperfections on the real compression members behaviour is illustrated by the comparison of imperfect beam-columns resistance and the resistance of their perfect counterparts. Numerous FEM simulations with regard to the stability behaviour of laterally and torsionally restrained steel structural elements of hot-rolled wide flange HEB section subjected to both compression and bending about the major or minor principal axes were performed. Geometrically and materially nonlinear analyses, GMNA for perfect structural elements and GMNIA for imperfect ones, preceded by LBA for the initial curvature evaluation of imperfect member configuration prior to loading were carried out. Numerical modelling and simulations were conducted with use of ABAQUS/Standard program. FEM results are compared with those obtained using the Eurocode’s interaction criteria of Method 1 and 2. Concluding remarks with regard to a necessity of equivalent imperfection profiles inclusion in modelling of the in-plane resistance of compression members are presented.