Simulation studies of the hobbing process kinematics can effectively improve the accuracy of the machined gears. The parameters of the cut-off layers constitute the basis for predicting the cutting forces and the workpiece stress-strain state. Usually applied methods for simulation of the hobbing process are based on simplified cutting schemes. Therefore, there are significant differences between the simulated parameters and the real ones. A new method of hobbing process modeling is described in the article. The proposed method is more appropriate, since the algorithm for the momentary transition surfaces formation and computer simulation of the 3D chip cutting sections are based on the results of hobbing cutting processes kinematics and on rheological analysis of the hob cutting process formation. The hobbing process is nonstationary due to the changes in the intensity of plastic strain of the material. The total cutting force is represented as a function of two time-variable parameters, such as the chip’s 3D parameters and the chip thickness ratio depending on the parameters of the machined layer.
Development of mineral deposits located at significant depth may be carried out by means of vertical shafts. Shaft sinking technology usually requires a number of works to be carried out, including the selection of appropriate excavating techniques adapted to geological and hydrological conditions, including natural hazards. The production technology and the machines used determine the level of sinking costs and execution period. The article discusses the excavating technologies currently used across the world. Then the assumptions, concept and construction of a new generation of shaft sinking system were presented. The proposed new solution of the system and the excavating technology allow for parallel execution of key processes related to winning, loading, transport and shaft wall-side lining, which significantly increases the progress of sinking. The shaft sinking system was created by scientists from AGH in cooperation with KOPEX – Przedsiębiorstwo Budowy Szybów S. A. and Instytut Techniki Górniczej KOMAG.
Automation of machining operations, being result of mass volume production of components, imposes more restrictive requirements
concerning mechanical properties of starting materials, inclusive of machinability mainly. In stage of preparation of material, the
machinability is influenced by such factors as chemical composition, structure, mechanical properties, plastic working and heat treatment,
as well as a factors present during machining operations, as machining type, cutting parameters, material and geometry of cutting tools,
stiffness of the system: workpiece – machine tool – fixture and cutting tool.
In the paper are presented investigations concerning machinability of the EN AC-AlSi9Cu3(Fe) silumin put to refining, modification and
heat treatment. As the parameter to describe starting condition of the alloy was used its tensile strength Rm. Measurement of the machining
properties of the investigated alloy was performed using a reboring method with measurement of cutting force, cutting torque and cutting
power. It has been determined an effect of the starting condition of the alloy on its machining properties in terms of the cutting power,
being indication of machinability of the investigated alloy. The best machining properties (minimal cutting power - Pc=48,3W) were
obtained for the refined alloy, without heat treatment, for which the tensile strength Rm=250 MPa. The worst machinability (maximal
cutting power Pc=89,0W) was obtained for the alloy after refining, solutioning at temperature 510 o
C for 1,5 hour and aged for 5 hours at
temperature 175 o
C. A further investigations should be connected with selection of optimal parameters of solutioning and ageing
treatments, and with their effect on the starting condition of the alloy in terms of improvement of both mechanical properties of the alloy
and its machining properties, taking into consideration obtained surface roughness.
This article deals with the technology and principles of the laser cutting of ductile cast iron. The properties of the CO2laser beam, input parameters of the laser cutting, assist gases, the interaction of cut material and the stability of cutting process are described. The commonly used material (nodular cast iron - share of about 25% of all castings on the market) and the method of the laser cutting of that material, including the technological parameters that influence the cutting edge, are characterized. Next, the application and use of this method in mechanical engineering practice is described, focusing on fixing and renovation of mechanical components such as removing the inflow gate from castings with the desired quality of the cut, without the further using of the chip machining technology. Experimental samples from the nodular cast iron were created by using different technological parameters of laser cutting. The heat affected zone (HAZ), its width, microstructure and roughness parameter Pt was monitored on the experimental samples (of thickness t = 13 mm). The technological parameters that were varied during the experiments included the type of assist gases (N2and O2), to be more specific the ratio of gases, and the cutting speed, which ranged from 1.6 m/min to 0.32 m/min. Both parameters were changed until the desired properties were achieved.
A short literature survey which justifies coating of ceramic cutting inserts is presented. The results reported are on selected nitride
coatings, in particular nanoscale multilayer, with layers of type Ti-Zr-N, TiN, ZrN and (TiAl)N, deposited by the arc PVD method on oxidecarbide ceramic cutting inserts of type TACN and TW2 produced at the Institute of Advanced Manufacturing Technology. Measurements and quality assessments were made, including of thickness of the coatings and of their constituent micro and nanolayers, microhardness of the coating and of the substrate, surface roughness of the inserts and of the cylindrical workpieces turned with these tools. Lifetimes of the coated and uncoated inserts were compared in turning an alloy tool steel. A significant increase in lifetime of the coated TW2 cutting tools was shown.
In this paper, the basic cutting characteristics such as cutting forces, cutting power and its distribution, specific cutting energies were determined taking into account variable tool corner radius ranging from 400 to 1200 μm and constant cutting parameters typical for hard turning of a hardened 41Cr4 alloy steel of 55 ± 1 HRC hardness. Finish turning operations were performed using chamfered CBN tools. Moreover, selected roughness profiles produced for different tool corner radius were compared and appropriate surface roughness parameters were measured. The measured values of Ra and Rz roughness parameters are compared with their theoretical values and relevant material distribution curves and bearing parameters are presented.
The contemporary underground mining of raw minerals is more and more associated with geological and mining software packages which support the work of designers from the moment of the exploration of a deposit, determination of its size and quality, geological, hydrogeological and tectonic conditions, by planning the development and cutting of the deposit. Production planning is one of the most important activities carried out in the course of a mining project, because it allows to set specific production results of a mine in relation to a time unit, and then allows for a verification of the degree of completion of the assumed plan. At present, computer-aided design is applicable to daily or long-term output planning taking deposit, qualitative, quantitative and cost constraints into account. In the article, selected forms of ore deposits were presented. On the basis of several dozen boreholes up to 300m in length, an exemplary fragment of the ore cutting model using computer-aided design of mining works was presented. By using modern computer software - ABB MineScape with modular construction, the possibilities of improving the process of development of future exploitation areas have been determined. In particular, the arrangement of boreholes, based on which ones the cross sections were made with, present the exemplary lithostratigraphic thickness of layers, including the location of discontinuous deformations in the form of faults, and an ore bearing zone. For the block model, resources with priority for metal N o. 1 and 2 were calculated. I n the last section of the article, the cutting idea for a shallow ore deposit has been presented. The degree of effective use of the deposit has been analysed for the room and pillar mining method.
The purpose of this paper is to focus on the loss separation of non-grain-oriented electrical steels used for speed-variable rotating electrical machines. The impact of laser-cutting, used in prototype manufacturing and of flux density harmonics, occurring locally in the lamination, on the loss distribution is studied in detail. Iron losses occurring under operation can physically be separated in different loss components. In this paper, a frequency-based loss model with parameters identified for single-sheet tester specimens, cut in strips of different widths, is therefore used. Moreover, a time-domain approach considers loss distributions occurring from higher harmonics. Hysteresis losses having high sensitivity to cut edge effects are calculated by the well-known Jiles-Atherton model adapting the frequency-based loss parameters. The model is validated by free-curve measurements at a single-sheet tester. It has been shown that the studied elliptical hysteresis model becomes inaccurate particularly for specimens with small strip widths with similar dimensions as teeth of electrical machine laminations. The incorrect mapping of losses occurring from minor hysteresis loops due to higher harmonics is concluded. The results showconsequently that both, the impact of a cut edge effect and local distributions of flux density harmonics need to be considered in terms of accurate iron loss prediction of electrical machine design.
The binary classifiers are appropriate for classification problems with two class labels. For multi-class problems, decomposition techniques, like one-vs-one strategy, are used because they allow the use of binary classifiers. The ensemble selection, on the other hand, is one of the most studied topics in multiple classifier systems because a selected subset of base classifiers may perform better than the whole set of base classifiers. Thus, we propose a novel concept of the dynamic ensemble selection based on values of the score function used in the one-vs-one decomposition scheme. The proposed algorithm has been verified on a real dataset regarding the classification of cutting tools. The proposed approach is compared with the static ensemble selection method based on the integration of base classifiers in geometric space, which also uses the one-vs-one decomposition scheme. In addition, other base classification algorithms are used to compare results in the conducted experiments. The obtained results demonstrate the effectiveness of our approach.