Accommodation tourist industry is characterized by high variability. For this category of services not only the location is crucial- that does not change, but also the standard, prices and seasonality of services. In the recent years, leisure centers performing functions only during the summer time have seen the possibility to extend their activities beyond the summer months. The reasons for this are the local investments requiring qualified staff which comes from different parts of the country, Europe and the world while creating dernand for accommodations. To meet the possible demand needs and to adapt to cold season, performing thermo-modernization works is necessary. In order to find the best solution and answer those needs, analysis of the profitability of the investrnents in a chosen holiday resort was carried out. The article presents the results of the analysis based on the payback period, LCC analysis and assessment of the investments risk.
Calculations were performed of the thermal system of a power plant with installed water pressure tanks. The maximum rise in the block electric power resulting from the shut-off of low-pressure regenerative heaters is determined. At that time, the boiler is fed with hot water from water pressure tanks acting as heat accumulators. Accumulation of hot water in water tanks is also proposed in the periods of the power unit small load. In order to lower the plant electric power in the off-peak night hours, water heated in low-pressure regenerative heaters and feed water tank to the nominal temperature is directed to water pressure tanks. The water accumulated during the night is used to feed the boiler during the period of peak demand for electricity. Drops in the power block electric power were determined for different capacities of the tanks and periods when they are charged. A financial and economic profitability analysis (of costs and benefits) is made of the use of tanks for a 200 MW power unit. Operating in the automatic system of frequency and power control, the tanks may also be used to ensure a sudden increase in the electric power of the unit. The results of the performed calculations and analyses indicate that installation of water pressure tanks is well justified. The investment is profitable. Water pressure tanks may not only be used to reduce the power unit power during the off-peak night hours and raise it in the periods of peak demand, but also to increase the power capacity fast at any time. They may also be used to fill the boiler evaporator with hot water during the power unit start-up from the cold state.
The paper covers problems of the owners of a fleet of long-operated conventional power plants that are going to be decommissioned soon in result of failing to achieve new admissible emissions levels or exceeding pressure elements design lifetime. Energoprojekt-Katowice SA, Siemens AG and Rafako SA presents their joint concept of the solution which is a 2on1 concept – replacing two unit by two ultra-supercritical boilers feeding one turbine. Polish market has been taken as an example.
The article investigates the influence of the carbody vertical flexibility on the ride comfort of the railway vehicles. The ride comfort is evaluated via the comfort index calculated in three reference points of the carbody. The results of the numerical simulations bring attention to the importance of the carbody symmetrical vertical bending upon the dynamic response of the vehicle, mainly at high velocities. Another conclusion is that the ride comfort can be significantly affected as a function of the symmetrical bending frequency of the carbody. Similarly, there are improvement possibilities for the ride comfort when the best selection of the stiffness in the longitudinal traction system between the carbody and bogie and the vertical suspension damping is made.
The article presents an overview of polymeric materials for flexible substrates in photovoltaic (PV) structures that could be used as power supply in the personal electronic systems. Four types of polymers have been elected for testing. The first two are the most specialized and heat resistant polyimide films. The third material is transparent polyethylene terephthalate film from the group of polyesters which was proposed as a cheap and commercially available substrate for the technology of photovoltaic cells in a superstrate configuration. The last selected polymeric material is a polysiloxane, which meets the criteria of high elasticity, is temperature resistant and it is also characterized by relatively high transparency in the visible light range. For themost promising of these materials additional studies were performed in order to select those of them which represent the best optical, mechanical and temperature parameters according to their usage for flexible substrates in solar cells.
This paper concerns an approach to model the ledger-stand joints of modular scaffolds. Based on the analysis of the working range of the ledger (represented by a linear relationship between load and displacement), two models of the ledger-stand joint are analysed: first – with flexibility joints and second – with rigid joints and with a transition part of lower stiffness. Parameters are selected based on displacement measurements and numerical analyses of joints, then they are verified. On the basis of performed research, it can be stated that both methods of joint modelling recommended in this paper, can be applied in engineering practices.
The awareness of the growing importance of the complexity in creating a new type of a modern enterprise strategy and in introducing changes within planning, control and organizational structures contributed to undertaking studies on relationships occurring between the complexity of a modern enterprise and its flexibility in the sector of industrial automation, as well as filling the gap relating to the cognitive impact of poor complexity management on the flexibility of the company. The main objective of the research work is to check whether there is an important relationship between the complexity of the business and its flexibility in the industrial automation sector. Quantification of the relationship between these two quantities – the complexity and flexibility – happened by the use of the Multidimensional Correspondence Analysis (MCA) and Perceptual Maps. The study which has been carried out indicated that the flexibility and complexity functions in the enterprise management rise, however, the knowledge of these issues is highly insufficient. The research discovered that the obstacles which hamper striking a balance between the flexibility and complexity in their advanced stages exert a devastating impact on the quality of the process management. Reducing the flexibility at its higher levels generates a context in which the market risk is enhanced. Companies characterised by improper flexibility management bear higher workforce costs and their processes of decision-making last longer. Methodical and systematized study of flexibility and complexity will decrease the destructive influence of the interaction between these two categories.
In the present work, an experimental investigation of a transverse fatigue crack has been carried out. A mathematical modelling of cracked rotor system along with the measured vibration is used to find crack parameters that not only detect the fault but also quantify it. Many experimental studies on cracks considered the crack as a slit or notch, which remains open. However, such flaws do not mimic a fatigue crack behavior, in which crack front opens and closes (i.e., breathes in a single revolution of the rotor). The fatigue crack in rotors commonly depicts 2x frequency component in the response, as well as higher frequency components, such as 3x, 4x and so on. In rotors, both forward and backward whirling take place due to asymmetry in rotor, and thus the fatigue crack gives the forward and backward whirl for all such harmonics. A rotor test rig was developed with a fatigue crack in it; rotor motions in two orthogonal directions were captured from the rig at discrete rotor angular speeds using proximity probes. The directional-spectrum processing technique has been utilized to the measured displacements to get its forward and backward whirl components. Subsequently, it is executed in a mathematical model-based estimation procedure to obtain the crack forces, residual unbalances, and remaining rotor system unknown variables. Estimation of crack forces during rotation of the shaft gives its characteristics, which can be used further to develop newer crack models.
Today’s manufacturing environment is highly uncertain, and it is continuously changing. It
is characterized by shorter life cycles of products and technologies, shorter delivery times, an
increased level of customization at the price of a standard product, increased product variety,
quality as well as demand variability and intense global competition. Academicians, as well as
practitioners, agree that uncertainty will continue to grow in the twenty-first century. To deal
with the uncertainties in demand variation and production capacity a manufacturing system
is required which can be easily reconfigured when there is a need at low cost. A reconfigurable
manufacturing system is such a type of system.
In the present work, the concept of the reconfigurable manufacturing system has been discussed
and reviewed. It has been compared with dedicated systems and flexible manufacturing
systems. Part family formation and barriers of reconfiguration also have been discussed.
This work is an attempt to contribute to the conceptual systematization of the reconfigurable
manufacturing system and reconfigurability by synthesizing the vast literature available after
a systematic review.
The article concerns modern, flexible adhesive joints, which might be used in timber construction. The article discusses the test results carried out for timber elements joints using polymeric adhesives produced by Sika®. The scope of the tests includes the analysis of strength criteria, tests of polymer adhesion to the timber with a pull-off method, tests of polymer layer shearing between timber elements as well as examination of bending of timber elements joined with polymer. The conclusions indicate the types of these polymers which are recommended for the creation of polymeric joints of timber-polymeric type in timber constructions.
This paper presents a study of the hybrid electro-discharge mechanical machining BEDMM (Brush Electro-Discharge Mechanical Machining) with the application of a rotary disk brush as a working electrode. The discussed method enables not only an effective machining with a material removal rate of up to 300 mm3/min but also finishing (with the obtained roughness of Ra < 0.5 μm) of the surfaces of complex-shaped alloys with poor machinability. The analysis of the factors involved in the machining process indicates that its efficiency is determined by electrodischarge. The use of flexible working electrodes makes it possible to apply simple technological instrumentation and results in the simplicity of the process automation. The aim of the study was to obtain quantitative relationships between the parameters of brush electro discharge mechanical machining (BEDMM) and its effects. The presented experimental research results define the effect of the process input parameters on the performance and roughness of machined surfaces obtained for manganese cast steel.
Many variants of thin film technology are nowadays part of the photovoltaic market. The most popular are amorphous silicon, CIS (Copper Indium Selenide)/CIGS (Copper Indium Gallium Selenide)/CIGSS (Copper Indium Gallium Sulphur Selenide), and CdS/CdTe (Cadmium Sulphide/Cadmium-Telluride) cells. All mentioned types allow potentially for a flexible cell structure. Most emitter contacts are currently based on TCOs (Transparent Conductive Oxides), however, wider approach with alternative carbon nanoforms, silver nanolayers and polymer materials, called TCLs (Transparent Conductive Layers) are also in use. Authors decided to investigate influence of mechanical stresses on physical and electrical behaviour of these layers. Consequently, the aim of work is to determine the level and possible mechanisms of flexible a-Si cell parameters degradation due to a deterioration of transparent contact properties.
The paper describes a research on assessing the quality of edges resulting from the interaction of laser pulses with a material of rigid and flexible printed circuits. A modern Nd:YVO4 crystal diode-pumped solid-state laser generating a 532 nm wavelength radiation with a nanosecond pulse time was used for the research. Influence of laser parameters such as beam power and pulse repetition frequency on a heat affected zone and carbonization was investigated. Quality and morphology of laser-cut substrates were analyzed by optical microscopy. High quality laser cutting of printed circuit board substrates was obtained without delamination and surface damage, with a minimal carbonization and heat affected zone. The developed process was implemented on the printed circuit assembly line.
This article takes up the matter of contemporary threats to cities and urbanity, setting the problems cities face today against the background of the two categories of the resilient city and the city developing sustainably. The author describes and presents the evolution of the sustainable development concept as such, as well as the generational change in priorities that has taken place where the development of urbanised areas is concerned, given the way the concept has undergone a certain devaluation, in the light of its failure to achieve fulfi lment. The challenges cities face today require multi-faceted activity, in respect of increased inclusivity, robustness and resilience, and flexibility. This leaves today’s idea of the resilient city embracing old elements of the sustainable city, but also augmenting them in various ways.
The functioning of a person affected with a chronic illness within a family is a complex and many-sided issue.
As family members form a system reflecting a network of mutual relations, one of the members’ illness will affect all those interacting with him / her emotionally. Keeping high-quality marital relations also becomes extremely difficult. The research covered 108 families (216 person) divided into three groups.We used an interview, the FACES IV questionnaire based on the Circumplex Model by David H. Olson and Dyadic Adjustment Scale (DAS) developed by Spanier.
Presence of multiple sclerosis (MS) in the family turned out to impact its functioning. The present research has found that the spouses’ gender of key importance for the family. Those families in which the woman was ill were characterized by excessive rigidity. On the other hand, where the multiple sclerosis sufferer was male, the system was overly chaotic.
Based on the research, it is highly probable that the majority of families with multiple sclerosis sufferers adjust relatively well to the disease. It can be supposed that the majority of multiple sclerosis affected families have developed an adaptive mechanism that benefits the patient. Supposedly, successful coping with disease may be determined by the caregiver's gender. This does not mean, however, that such families are free from problems. The difficulties relate primarily to communication, excessive autocracy, developing their individuality and autonomy. Therapeutic support for the patient and his / her family should therefore be a vital component of the treatment process.