The aim of this paper is to study the applicability of the theory of micropolar fluids to modelling and calculating flows in microchannels depending on the geometrical dimension of the flow field. First, it will be shown that if the characteristic linear dimension of the flow becomes appropriately large, the equations describing the micropolar fluid flow can be transformed into Navier-Stokes equations. Next, Poiseuille flows in a microchannel is studied in detail. In particular, the maximal cross-sectional size of the channel for which the micropolar effects of the fluid flow become important will be established. The experimentally determined values of rheological constants of the fluid have been used in calculations.
This study aims to design a novel air cleaning facility which conforms to the current situation in China, and moreover can satisfy our demand on air purification under the condition of poor air quality, as well as discuss the development means of a prototype product. Air conditions in the operating room of a hospital were measured as the research subject of this study. First, a suitable turbulence model and boundary conditions were selected and computational fluid dynamics (CFD) software was used to simulate indoor air distribution. The analysis and comparison of the simulation results suggested that increasing the area of air supply outlets and the number of return air inlets would not only increase the area of unidirectional flow region in main flow region, but also avoid an indoor vortex and turbulivity of the operating area. Based on the summary of heat and humidity management methods, the system operation mode and relevant parameter technologies as well as the characteristics of the thermal-humidity load of the operating room were analyzed and compiled. According to the load value and parameters of indoor design obtained after our calculations, the airflow distribution of purifying the air-conditioning system in a clean operating room was designed and checked. The research results suggested that the application of a secondary return air system in the summer could reduce energy consumption and be consistent with the concept of primary humidity control. This study analyzed the feasibility and energy conservation properties of cleaning air-conditioning technology in operating rooms, proposed some solutions to the problem, and performed a feasible simulation, which provides a reference for practical engineering.
This paper presents the results of experimental testing of parameters of the flow of an agitated liquid in a stirred tank with an eccentrically positioned shaft and with a Rushton turbine. The investigations were focused on the impact of the stirrer shaft shift in relation to the stirred tank vertical axis on the agitated liquid mean velocities and the liquid turbulent velocity fluctuations, as well as on the turbulence intensity in the tank. All the experiments were carried out in a stirred tank with the inner diameter of 286 mm and a flat bottom. The adopted values of the shaft eccentricity were zero (central position) and half the tank radius. The liquid flow instantaneous velocities were measured using laser Doppler anemometry.
Plate fin-tube heat exchangers fins are bonded with tubes by means of brazing or by mechanical expansion of tubes. Various errors made in the process of expansion can result in formation of an air gap between tube and fin. A number of numerical simulations was carried out for symmetric section of plate fin-tube heat exchanger to study the influence of air gap on heat transfer in forced convection conditions. Different locations of air gap spanning 1/2 circumference of the tube were considered, relatively to air flow direction. Inlet velocities were a variable parameter in the simulations (1– 5 m/s). Velocity and temperature fields for cases with air gap were compared with cases without it (ideal thermal contact). For the case of gap in the back of the tube (in recirculation zone) the lowest reduction (relatively to the case without gap) of heat transfer rate was obtained (average of 11%). The worst performance was obtained for the gap in the front (reduction relatively to full thermal contact in the average of 16%).
The optimization of finned tube heat exchanger is presented focusing on different fluid velocities and the consideration of aerodynamic configuration of the fin. It is reasonable to expect an influence of fin profile on the fluid streamline direction. In the cross-flow heat exchanger, the air streams are not heated and cooled evenly. The fin and tube geometry affects the flow direction and influences temperature changes. The heat transfer conditions are modified by changing the distribution of fluid mass flow. The fin profile impact also depends on the air velocity value. Three-dimensional models are developed to find heat transfer characteristics between a finned tube and the air for different air velocities and fin shapes. Mass flow weighted average temperatures of air volume flow rate are calculated in the outlet section and compared for different fin/tube shapes in order to optimize heat transfer between the fin material and air during the air flow in the cross flow heat exchanger.
In this study, the process of membrane cleaning by supercritical fluid extraction was investigated. Polypropylene microfiltration membranes, contaminated with oils, were treated in a batch process with a supercritical fluid (SCF). As extractant, pure supercritical carbon dioxide or supercritical carbon dioxide with admixtures of methanol, ethanol and isopropanol were used. Single-stage and multi-stage extraction was carried out and process efficiency was determined. The obtained results showed that addition of organic solvents significantly enhances the cleaning performance, which increases with increase of organic solvent concentration and decreases with increasing temperature. All three solvents showed a comparable effect of efficiency enhancement. The results confirmed that supercritical fluid extraction can be applied for polypropylene membrane cleaning.
The aim of the project was to collect experimental data regarding local distributions of fluid velocity and inert tracer concentration in a tank reactor with turbulent flow. The experiments were performed in a microscale in a region of tracer fluid injection. The results of experiments can be used for direct validation of currently developed CFD models, particularly for time-dependent mixing models used in LES.
The results of investigations of the rheological properties of typical ceramic slurries used in the investment casting technology – the lost
wax technology are presented in the paper. Flow curves in the wide range of shear velocity were made. Moreover, viscosity of ceramic
slurries depending on shearing stresses was specified. Tests were performed under conditions of three different temperatures 25, 30 and
35oC, which are typical and important in the viewpoint of making ceramic slurries in the investment casting technology.
In the light of the performed investigations can be said that the belonging in group of Newtonian or Non – Newtonian fluid is dependent
on content of solid phase (addition of aluminum oxide) in the whole composition of liquid ceramic slurries.
In the paper there are presented tools for structural modelling of throttle diagrams that are developed as a basis to building transducers used for measuring fluid parameters. The definitions of throttle diagrams are improved and their classification is developed. Dependences are obtained to calculate the number of measuring channels in a throttle diagram and the number of possible variants of measuring transducers using the combinatory apparatus. A procedure for mathematical description of throttle diagrams in the form of graphs is proposed which makes it possible to obtain all diagrams with different measuring channels on the basis of certain throttle diagram. The model is developed in the form of a graph. A schematic diagram and a mathematical model of a transducer measuring physical and mechanical parameters of Bingham plastic fluid are developed based on a throttle diagram.
The joined wing concept is an unconventional airplane configuration, known since the mid-twenties of the last century. It has several possible advantages, like reduction of the induced drag and weight due to the closed wing concept. The inverted joined wing variant is its rarely considered version, with the front wing being situated above the aft wing. The following paper presents a performance prediction of the recently optimized configuration of this airplane. Flight characteristics obtained numerically were compared with the performance of two classical configuration airplanes of similar category. Their computational fluid dynamics (CFD) models were created basing on available documentation, photographs and some inverse engineering methods. The analysis included simulations performed for a scale of 3-meter wingspan inverted joined wing demonstrator and also for real-scale manned airplanes. Therefore, the results of CFD calculations allowed us to assess the competitiveness of the presented concept, as compared to the most technologically advanced airplanes designed and manufactured to date. At the end of the paper, the areas where the inverted joined wing is better than conventional airplane were predicted and new research possibilities were described.
In this study, the vibration analysis of fully and partially treated laminated composite Magnetorheological (MR) fluid sandwich plates has been investigated experimentally. The natural frequencies of fully and partially treated laminated composite MR fluid sandwich plates have been measured at various magnetic field intensities under two different boundary conditions. The variations of natural frequencies with applied magnetic field, boundary conditions and location ofMRfluid pocket have been explored. Further, a comparison of natural frequencies of fully and partially treated MR fluid sandwich structure has been made at various magnetic field intensities.