Activities of the Polish research gSDroups concerning gravity field modelling and gravimetry in a period of 2015–2018 are reviewed and summarised in this paper. The summary contains the results of research on the evaluation of GOCE-based global geopotential models (GGMs) in Poland and geoid modelling. Extensive research activities are observed in the field of absolute gravity surveys, in particular for the maintenance of national gravity control in Poland, Sweden, Denmark, the Republic of Ireland and in Northern Ireland as well as for geodynamics with special emphasis on metrological aspects in absolute gravimetry. Long term gravity variations were monitored in two gravimetric laboratories: the Borowa Gora Geodetic-Geophysical Observatory, and Jozefoslaw Astrogeodetic Observatory with the use of quasi-regular absolute gravity measurements as well as tidal gravimeter records. Gravity series obtained were analysed considering both local and global hydrology effects. Temporal variations of the gravity field were investigated using data from GRACE satellite mission as well as SLR data. Estimated variations of physical heights indicate the need for kinematic realization of reference surface for heights. Also seasonal variability of the atmospheric and water budgets in Poland was a subject of investigation in terms of total water storage using the GLDAS data. The use of repeatable absolute gravity data for calibration/validation of temporal mass variations derived from satellite gravity missions was discussed. Contribution of gravimetric records to seismic studies was investigated. The bibliography of the related works is given in references.
In this paper a cross-shaped isolator consisting of cuboidal magnets and a cylindrical isolator are compared by resonance frequency to volume ratio and shape. Both isolators are capable of obtaining a low resonance frequency, i.e. 0.15 Hz and 0.01 Hz for the cross and cylinder, respectively. The volume of both isolators is comparable, only the shape is different, resulting in a tall structure with a small footprint for the cross and a flat with a large diameter cylindrical structure. A sensitivity analysis shows that due to the large amount of magnets, the cross-shaped isolator is less sensitive to manufacturing tolerances.
When conducting geodetic and gravimetric measurements, there is a problem of projecting them to the reference surface. Since the gravitational field is inhomogeneous under the real conditions, the problem arises of determining the corrections to the measured values of gravitational acceleration in order to use the obtained data for the subsequent solutions of projection problems. Currently, the solution to this problem is performed using a Bouguer reduction, which requires information about the internal structure of the upper layer of the earth’s surface, topography, etc. The purpose of this study is to develop a methodological approach that would allow to determine the reduction (projection) corrections for gravitational acceleration on technogenic and geodynamic polygons without using data about the distribution of surface layer density and topography. The research process is based on the use of mathematical analysis methods and a wide range of experimental geodetic and gravimetric measurements. In the course of the performed researches, an algorithm was obtained and a practical implementation of the determination of the corrections in the measured values of gravitational acceleration on the basis of geodetic and gravimetric measurements was carried out at the certain geodynamic polygon in order to bring all corrections to one level surface.
Research activities of Polish research groups in a period of 2015–2019 on reference frames and reference networks are reviewed and summarised in this paper. The summary contains the results concerning the implementation of latest resolutions on reference systems of the International Union of Geodesy and Geophysics and the International Union of Astronomy with special emphasis on the changes in the Astronomical Almanac of the Institute of Geodesy and Cartography, Warsaw. It further presents the status of the implementation of the European Terrestrial Reference System 1989 (ETRS89) in Poland, monitoring the terrestrial reference frame, operational work of GNSS permanent IGS/EPN stations in Poland, operational work of the laser ranging station in Poland of the International Laser Ranging Service (ILRS), active GNSS station network for the realization of ETRS89 in Poland, validation of recent ETRS89 realization, expressed in ETRF2000 in Poland, and maintenance of the vertical control in Poland (PL-KRON86-NH). Extensive research activities are observed in the field of maintenance and modernization of gravity control not only in Poland, but also in Sweden and in Denmark, as well as establishment of gravity control in Ireland based on absolute gravity survey. The magnetic control in Poland was also regularly maintained. The bibliography of the related works is given in references.
The theory of generalized two-temperature thermoelasticity is used to solve the boundary value problems between two elastic media with two different types of temprature under the influence of gravity.The classical dynamical coupled theory and Lord-Şhulman theory are used to obtain the general solution of the governing equations and investigate the effect of surface waves in an isotropic elastic medium subjected to gravity field. The harmonic vibrations method is used to obtain the displacement components, stress tensor and temperature distribution in the considerd physical domain with comparison with the two theories. The obtained analytic solution of the problem is applied for special cases for which the effect of two temperatures is studied. The conductive and dynamical temperatures as well as stress and strain components are shown graphically for a suitable material. Some comparisons are also introduced in the absence and in the presence of gravity, and two-temperature parameter. The differences in the obtained results between the two theories are considered.
The paper is devoted to study the effect of gravity, magnetic field and laser pulse on the general model of the equations of generalized thermoelasticity for a homogeneous isotropic elastic half-space. The formulation is applied under four theories of generalized thermoelasticity: the coupled theory, Lord-Schulman theory, Green-Lindsay theory as well as Green-Naghdi theory. By employing normal mode analysis, the analytical expressions for the displacement components, temperature and the (mechanical and Maxwell’s) stresses distribution are obtained in the physical domain. These expressions are also calculated numerically and corresponding graphs are plotted to illustrate and compare the theoretical results. The effect of gravity, magnetic field and laser pulse are also studied and displayed graphically to show the physical meaning of the phenomena. A comparison has been made between the present results and the results obtained by the others. The results indicate that the effects of magnetic field, laser pulse and gravity field are very pronounced.
The paper reports the results of a physical modelling study of the production of a hypereutectic aluminium alloy to be used for making an alloy vapour source for operation in the magnetron. Within the study, targets from a hypereutectic aluminium-silicon alloy were made in laboratory conditions. Thus obtained material was subjected to heat treatment, porosity analysis, and the assessment of the microstructure and fitness for being used in the magnetron. The process of melting the hypereutectic Al-Si alloy was carried out at the Department of Foundry of the Czestochowa University of Technology. The investigation into the production of the alloy vapour source for the synthesis of the dielectric material from the hypereutectic aluminium alloy has confirmed.
The paper, which is a summary and supplement of previous works and research, presents the results of numerical and physical modeling of the GX2CrNiMoCuN25-6-3 duplex cast steel thin-walled castings production. To obtain thin-walled castings with wall in the thinnest place even below 1 mm was used the centrifugal casting technology and gravity casting. The analyzed technology (centrifugal casting) enables making elements with high surface quality with reduced consumption of batch materials and, as a result, reducing the costs of making a unitary casting. The idea behind the production of cast steel with the use of centrifugal technology was to find a remedy for the problems associated with unsatisfactory castability of the tested alloy.
The technological evaluation of the cast construction was carried out using the Nova Flow & Solid CV 4.3r8 software. Numerical simulations of crystallization and cooling were carried out for a casting without a gating system and sinkhead located in a mold in accordance with the pouring position. It was assumed that the analyzed cast will be made in the sand form with dimensions 250×250×120 mm.