Bentonite is clay rock, which is created by decomposition of vulcanic glass. It is formed from mixture of clay minerals of smectite group,

mainly montmorillonite, beidellite and nontronite. Its typical characteristics is, that when in contact with water, it intensively swells. First

who used this term was W.C. Knight in 1887. The rock had been named after town Fort Benton in American state Montana. For its

interesting technological properties and whiteness has wide technological use. Bentonite is selectively mined and according to its final use

separately modified, which results in high quality product with specific parameters.

In the beginning of 21st century belong bentonite moulding mixtures in foundry to always perspective. Mainly increased ratio of ductile

cast iron castings production cannot be ensured without the need of quality bentonite. Great area of scope remains to further research of

moulding materials, which return also to bentonite producers.

In modern times, there are increasing requirements for products quality in every part of manufacturing industry and in foundry industry it

is not different. That is why a lot of foundries are researching, how to effectively produce castings with high quality. This article is dealing

with search of the influence of using different types of risers or chills on shrinkage cavity production in ductile iron castings. Differently

shaped risers were designed using the Wlodawer´s modulus method and test castings were poured with and without combination of chills.

Efficiency of used risers and chills was established by the area of created shrinkage cavity using the ultrasound nondestructive method.

There are introduced the production process of test castings and results of ultrasound nondestructive reflective method. The object of this

work is to determine an optimal type of riser or chill for given test casting in order to not use overrated risers and thus increase the cost

effectiveness of the ductile iron castings production.

The use of environmentally friendly inorganic binders and new technologies for cores production is widely discussed topic in recent years. This paper contains information about new hot curing process for core making with alumina-silicate based inorganic binders – geopolymers. Main differences between hot cured geopolymers and hot cured alkali silicate based inorganic binders are discussed. The main objective of this research paper was to investigate basic technological properties of geopolymer binder system such as strength, compaction, storage ability and knock-out properties. For this purpose, three mixtures with different powder additives were prepared and tested in laboratory conditions using specific methods. Strength properties evaluation showed sufficient levels as well as knock-out properties measurement, even with additives B and C originally designed for the use with alkali silicate based two component binder systems. Additives B and C were considered compatible with geopolymer binders after casting production trial results. Storage ability of geopolymers seems to be more sensitive than of alkali silicate based binders in the same tested conditions. Mixtures with geopolymer binder showed 20% more decrease of strength compared to alkali silicate binders after 24 hours in conditions of 25 °C and 65 %RH.

The main bulk density representation in the molding material is opening material, refractory granular material with a particle size of 0.02

mm. It forms a shell molds and cores, and therefore in addition to activating the surface of the grain is one of the most important features

angularity and particle size of grains. These last two features specify the porosity and therefore the permeability of the mixture, and

thermal dilatation of tension from braking dilation, the thermal conductivity of the mixture and even largely affect the strength of molds

and cores, and thus the surface quality of castings. [1]

Today foundries, which use the cast iron for produce of casts, are struggling with surface defects on the casts. One of these defects are

veining. They can be eliminated in several ways. Veining are foundry defects, which arise as a result of tensions generated at the interface

of the mold and metal. This tension also arises due to abrupt thermal expansion of silica sand and is therefore in the development of

veining on the surface of casts deal primarily influences and characteristics of the filler material – opening material in the production of

iron castings.

Currently is the biggest problem of metallurgical companies the increase of fossil fuel prices and strict environmental regulations. As a result of this, companies must look for alternatives that would reduce the amount of fossil fuels and reduce emissions. Wood sawdust has huge energy potential, which can be used in the process of agglomerate production. This type of energy is locally available, has some similar properties as fossil fuels and is economically advantageous. For these reasons, experimental study using laboratory agglomeration pan was realized to study the possibility of agglomerate production with a mixed fuel. Experimental results show the viability of mixed fuel use in the agglomeration process, but also show significant possibility for improvement. The maximum acceptable substitution ratio, which corresponds to qualitatively suitable agglomerate is 20% of pine sawdust. Based on the realized experiments and the obtained results we have acceded to the intensification of the agglomeration process with an objective to increase the amount of added substitution fuel while maintaining the required quality of agglomerate.

The main problem in the cores production by cold-box method is the occurence of surface defects due to the tension generated by thermal expansion of the silica sand. One of the possibilities of eliminination is exchange of silica sand from another location. Another interesting factor is the type of used binder and its amount. However, even these measures donʹt guarantee sufficient quality. Foundries most often solve this problem by adding expensive additives to the core mixture. Foundries may have a dilemma in choosing the right additive. The aim of this paper was to investigate the effect of silica sand from two different locations, the effect of dosing the amount of binder and the addition of several types of commonly available additives on the quality of casting cavities. For this purpose, a total of 11 differently composed core sand mixtures were prepared, but only one of these mixtures was successful.