Recently, the use of inorganic binders cured by heat as a progressive technology for large scale production of cores is widely discussed topic in aluminium foundries. As practical experiences show, knock-out properties of inorganic binders were significantly increased, although they cannot overcome organic based binder systems. This paper contains information about hot curing processes based on alkali silicate and geopolymer binder systems for core making. Main differences between hot cured geopolymers and hot cured alkali silicate based inorganic binders are discussed. Theory of geopolymer binder states, that binder bridge destruction is mainly of adhesive character. The main aim of this research paper was to examine binder bridge destruction of alkali silicate and geopolymer binder systems. In order to fulfil this objective, sample parts were submitted to defined thermal load, broken and by using SEM analysis, binder bridge destruction mechanism was observed. Results showed that geopolymer binder system examined within this investigation does not have mainly adhesive destruction of binder bridges, however the ratio of adhesive-cohesive to cohesive destruction is higher than by use of alkali silicate based binder systems, therefore better knock-out properties can be expected.

In modern times, there are increasing requirements for products quality in every part of manufacturing industry and in foundry industry it

is not different. That is why a lot of foundries are researching, how to effectively produce castings with high quality. This article is dealing

with search of the influence of using different types of risers or chills on shrinkage cavity production in ductile iron castings. Differently

shaped risers were designed using the Wlodawer´s modulus method and test castings were poured with and without combination of chills.

Efficiency of used risers and chills was established by the area of created shrinkage cavity using the ultrasound nondestructive method.

There are introduced the production process of test castings and results of ultrasound nondestructive reflective method. The object of this

work is to determine an optimal type of riser or chill for given test casting in order to not use overrated risers and thus increase the cost

effectiveness of the ductile iron castings production.

The use of environmentally friendly inorganic binders and new technologies for cores production is widely discussed topic in recent years. This paper contains information about new hot curing process for core making with alumina-silicate based inorganic binders – geopolymers. Main differences between hot cured geopolymers and hot cured alkali silicate based inorganic binders are discussed. The main objective of this research paper was to investigate basic technological properties of geopolymer binder system such as strength, compaction, storage ability and knock-out properties. For this purpose, three mixtures with different powder additives were prepared and tested in laboratory conditions using specific methods. Strength properties evaluation showed sufficient levels as well as knock-out properties measurement, even with additives B and C originally designed for the use with alkali silicate based two component binder systems. Additives B and C were considered compatible with geopolymer binders after casting production trial results. Storage ability of geopolymers seems to be more sensitive than of alkali silicate based binders in the same tested conditions. Mixtures with geopolymer binder showed 20% more decrease of strength compared to alkali silicate binders after 24 hours in conditions of 25 °C and 65 %RH.

The main bulk density representation in the molding material is opening material, refractory granular material with a particle size of 0.02

mm. It forms a shell molds and cores, and therefore in addition to activating the surface of the grain is one of the most important features

angularity and particle size of grains. These last two features specify the porosity and therefore the permeability of the mixture, and

thermal dilatation of tension from braking dilation, the thermal conductivity of the mixture and even largely affect the strength of molds

and cores, and thus the surface quality of castings. [1]

Today foundries, which use the cast iron for produce of casts, are struggling with surface defects on the casts. One of these defects are

veining. They can be eliminated in several ways. Veining are foundry defects, which arise as a result of tensions generated at the interface

of the mold and metal. This tension also arises due to abrupt thermal expansion of silica sand and is therefore in the development of

veining on the surface of casts deal primarily influences and characteristics of the filler material – opening material in the production of

iron castings.