The measured rate of release of intercellular protein from yeast cells by ultrasonication was applied for evaluating the effects of sonication reactor geometry on cell disruption rate and for validation of the simulation method. Disintegration of two strains of Saccharomyces cerevisiae has been investigated experimentally using a batch sonication reactor equipped with a horn type sonicator and an ultrasonic processor operating at the ultrasound frequency of 20 kHz. The results have shown that the rate of release of protein is directly proportional to the frequency of the emitter surface and the square of the amplitude of oscillations and strongly depends on the sonication reactor geometry. The model based on the Helmholtz equation has been used to predict spatial distribution of acoustic pressure in the sonication reactor. Effects of suspension volume, horn tip position, vessel diameter and amplitude of ultrasound waves on the spatial distribution of pressure amplitude have been simulated. A strong correlation between the rate of protein release and the magnitude of acoustic pressure and its spatial distribution has been observed. This shows that modeling of acoustic pressure is useful for optimization of sonication reactor geometry.
The exact measurement of multiphase flow is an important and essential task in the oil and petrochemical related industries. Several methods have already been proposed in this field. In the existing methods, flow rate measurement depends on the fluid flow pattern. Flow pattern recognition requiring calibration has created instability in such systems. In this paper, a imple and reliable method is proposed which is based on ultrasonic tomography. It is free from calibration and instability problems that existing methods have. The obtained data from a 32-digit array of ultrasonic sensors have been used and the two-phase flow rate including liquid and gas phases have been calculated through a simple algebraic algorithm. Simulation results show that while applying this method the measurement technique is independent from the fluid flow pattern and the system error is decreased. For the proposed algorithm, the average amount of the spatial imaging error (SIE) for a bubble at different positions inside the pipe is about 5%.
The aim of the research was to determine the effect of sonochemical treatments on homogenization of powders as well as phase composition and thermal stability of sinters. The compounds were prepared from Eu2O3 and ZrO2 powders, weighed in the mass ratio 1:1. Initially ultrasound treatment was applied. 750-Watt ultrasonic processor VCX-750 equipped with sealed converter VC-334 and horn 630-0219 with the diameter of 13 mm (Sonics & Materials, Inc.) was used as a source of ultrasound. Applied ultrasound frequency was 20 kHz, power density was controlled in the range from 75 W/cm2 to 340 W/cm2. Investigated compounds were synthesized via solid-state reaction (SSR). The Differential Scanning Calorimetry (DSC) was used in order to investigate the effect of sonochemical treatment on the synthesis of prepared mixtures the powders particle size distribution was analyzed. Ultrasound treatment what wasn’t never been reported before.
In this paper, three methods of sterilisation are compared to determine their usability in nanobubble dispersion sterilisation: filtration, thermal sterilisation and sonication (in two systems: using a sonotrode and sonication bath). Nanobubble dispersions are most commonly generated in non-sterile systems which precludes them from use in most biological research. As a result of this study, filtration was chosen as the best method for nanobubble sterilisation.
One major problem in the design of ultrasonic transducers results from a huge impedance mismatch between piezoelectric ceramics and the loading medium (e.g. gaseous, liquid, and biological media). Solving this problem requires the use of a matching layer (or layers). Optimal selection of materials functioning as matching layers for piezoelectric transducers used in transmitting and receiving ultrasound waves strictly depends on the type of the medium receiving the ultrasound energy. Several methods allow optimal selection of materials used as matching layers. When using a single matching layer, its impedance can be calculated on the basis of the Chebyshev, DeSilets or Souquet criteria. In the general case, the typically applied methods use an analogy to a transmission line in order to calculate the transmission coefficient T. This paper presents an extension of transmission coefficient calculations with additional regard to the attenuation coefficients of particular layers. The transmission coefficient T is optimised on the basis of a genetic algorithm method. The obtained results indicate a significant divergence between the classical calculation methods and the genetic algorithm method.
The paper presents and discusses a method of azimuth determination of ultrasonic echo arrival in air. The basis of the presented approach is the assumption that the received signal is a narrowband one. In this way, the direction of the signal arrival can be determined based on its phase shift using two receivers. When the distance between the receivers exceeds half of the wavelength of the received signal, a problem of ambiguity in determining the angle of arrival arises. To solve this, a method using multiple pairs of receivers was used. Its robustness and temperature dependence is analysed. The most important advantages of the presented approach are simplified computations and low hardware requirements. Experimental data made it possible to show that for strong echoes, the accuracy is higher than 0.5X. In the case of weak echos, it is reduced to about 2X. Because the method is based on phase shift measurement, the ultrasonic sonar that uses this method can be compact in size. Moreover, owing to the theoretical analysis, certain properties of the mutual location of the receivers were found and formally proved. They are crucial for determining proper receivers’ inter-distances.
The aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after 0.5 h in high temperature exposition. Different acoustic response for reference sample and sensitized samples were recorded. In this work, changes in share wave amplitude were measured.
The progressive development of miniature systems increases the demand for miniature parts. Reducing the size of manufactured components on one hand is a serious challenge for traditional technologies, but on the other hand, mainly by removing the energy barrier opens the possibility of using other unconventional techniques. A good example is the ultrasonic excitation of the punch during the micro-upsetting process. The anti-barreling phenomenon and dependent on the amplitude of vibrations, intensive deformation of the surface layers in contact with the tools at both ends of the sample was noted. Based on the measured strains and stresses, an increase in temperature in the extreme layers to approx. 200°C was suggested. By adopting a simplified dynamic model of the test stand, the possibility of detaching the surface of the punch from the surface of the sample was demonstrated.
This paper presents the results of acoustic field distribution simulations for the 1024-element ultrasonic ring array intended for the diagnosis of female breast tissue with the use of ultrasound tomography. For the purpose of analysing data, all acoustic fields created by each elementary transducer were combined. The natural position of the focus inside the ultrasonic ring array was changed by altering activation time of individual transducers in sectors consisting of 32, 64, and 128 ultrasonic transducers. Manipulating the position of the focus inside the array will allow to concentrate the ultrasonic beam in a chosen location in the interior space of the ring array. The goal of this research is to receive the best possible quality of images of cross-sections of the female breast. The study also analysed the influence of the acoustic field distribution on the inclination of the beam. The results will enable to choose an optimal focus and an optimal number of activated transducers.
This paper presents integration of ultrasonic and inertial approaches in indoor navigation system. Ultrasonic navigation systems allow to obtain good results whilst there are at least three beacon transmitters in the range of mobile receiver, but in many situations placement of large number of transmitters is not economically justified. In such situations navigation must be aided by other technique. This paper describes research on supporting ultrasonic system by inertial system based on Magnetic, Angular Rate and Gravity sensor. This can measure current orientation of the receiver and allows to estimate the length of the path by pedometer functionality.
The paper describes an innovative ultrasound imaging method called Doppler Tomography (DT), otherwise known as Continuous Wave Ultrasonic Tomography (CWUT). Thanks to this method, it is possible to image the tissue cross-section in vivo using a simple two-transducer ultrasonic probe and using the Doppler effect. It should be noted that DT significantly differs from the conventional ultrasound Doppler method of measuring blood flow velocity. The main difference is that when measuring blood flow, we receive information with an image of the velocity distribution in a given blood vessel (Nowicki, 1995), while DT allows us to obtain a cross-sectional image of stationary tissue structure. In the conventional method, the probe remains stationary, while in the DT method, the probe moves and the examined tissue remains stationary.
This paper presents a method of image reconstruction using the DT method. First, the basic principle of correlation of generated Doppler frequencies with the location of inclusions from which they originate is explained. Then the exact process and algorithm in this method are presented. Finally, the impact of several key parameters on imaging quality is examined. As a result, the conclusions of the research allow to improve the image reconstruction process using the DT method.
The paper presents results of numerical calculations and experimental data on the directional pattern of two 38-element parametric arrays composed of ultrasound sources. Two types of antenna arrays are considered, namely with parallel and coaxial connections of ultrasonic transducers (elements). The results of selecting and functional testing of unit elements are described in this paper. It is found that in the coaxial element connection of the antenna array, the level of side lobes is higher than that in the parallel element connection.
A π-phase-shifted fiber Bragg grating (π-FBG) shows high sensitivity to the ultrasonic (US) wave as compared to the conventional FBG due to the strong slow-light phenomenon at the resonance peak. However, its sensitivity is limited by the interrogation schemes. A combination of π-FBG and unbalanced fiber Mach– Zehnder interferometer (F-MZI) are theoretically analyzed and optimized for the highly sensitive acoustic sensor. The coupled-mode theory (CMT) and transfer matrix method (TMM) are used to establish the numerical modelling of π-FBG. For the optimized grating parameters of π-FBG, the proposed sensing system shows the high strain sensitivity of 1.2 × 108/ε, the highest dynamic strain resolution of 4.1fε/√Hz, and the highest wavelength shift resolution of 4.9 × 10−9 pm. Further, the proposed sensing system strongly supports both time andwavelength division multiplexing techniques. Therefore, the proposed sensing system shows extreme importance in single as well as quasi-distributed US acoustic wave sensing networks.
Entrapped gases, solidification shrinkage and non-metallic compound formation are main sources of porosity in aluminium alloy castings. Porosity is detrimental to the mechanical properties of these castings; therefore, its reduction is pursued. Rotary degassing is the method mostly employed in industry to remove dissolved gases from aluminium melts, reducing porosity formation during solidification of the cast part. Recently, ultrasonic degassing has emerged as a promising alternative thanks to a lower dross formation and higher energy efficiency. This work aims to evaluate the efficiency of the ultrasonic degasser and compare it to a conventional rotary degassing technique applied to an AlSi10Mg alloy. Degassing efficiency was evaluated employing the reduced pressure test (RPT), where samples solidified under reduced pressure conditions are analysed. Factors affecting RPT were considered and temperature parameters for the test were established. The influence of ultrasonic degassing process parameters, such as degassing treatment duration and purging gas flow rate were studied, as well as treated aluminium volume and oxide content. Finally, ultrasonic degassing process was contrasted to a conventional rotary degassing technique, comparing their efficiency.