The Copper-SiC composite was investigated with the help of FEM. The authors modeled and analyzed the effect of relaxation of thermal stresses due to seasoning at room temperature after the manufacturing process together with the effect of thermal stresses induced by reheating the material to a service temperature. Especially, hypothetical fracture at interface was of interest. It was shown that, for a fixed temperature, a single crack emanating at 0° or 45° azimuth would develop only along a portion of fiber perimeter, and a further growth would require stress increase in the fiber surrounding.

A thermoelastic boundary value problem of a hollow circular disc made of functionally graded materials with arbitrary gradient is analysed. The steady-state temperature distribution is assumed to be the function of the radial coordinate with prescribed temperature at the inner and outer cylindrical boundary surfaces. The material properties are assumed to be arbitrary smooth functions of the radial coordinate. A coupled system of ordinary differential equations containing the radial displacement and stress function is derived and used to get the distribution of thermal stresses and radial displacements caused by axisymmetric mechanical and thermal loads. General analytical solutions of functionally graded disc with thermal loads are not available. The results obtained by the presented numerical method are verified by an analytical solution. The considered analytical solution is valid if the material properties, except the Poisson ratio, are expressed as power functions of the radial coordinate.

This paper presents the methodology for determining thermal strains and stresses during heating the charge in a rotary furnace. The calculations were made with the original software, which uses the finite element method. The heat transfer boundary conditions used for computing were verified on the basis of industrial tests. Good compatibility between the experimental data and numerical calculations was obtained. The possibility of the material cracking occurrence was checked for a set exhaust gas temperature distribution on the furnace length. As a result, it was possible to develop steel heating curves characterized by short process times.

By the very nature of their work, castings used in furnaces for heat treatment and thermo-chemical treatment are exposed to the effect of many unfavorable factors causing their deformation and cracking, significantly shortening the lifetime. The main source of damage are the micro- and macro-thermal stresses appearing in each cycle. As the cost of furnace instrumentation forms a significant part of the total furnace cost, in designing this type of tooling it is important to develop solutions that delay the damage formation process and thus extend the casting operation time. In this article, two structural modifications introduced to pallets castings to reduce thermal stresses arising at various stages of the cooling process are proposed. The essence of the first modification consists in making technological recesses in the wall connections, while the aim of the second one is to reduce the stiffness of the pallet by placing expanders in the external walls. Using the results of simulation analyses carried out by the finite element method, the impact of both proposed solutions on the level of thermal stresses was evaluated.

The results of research on the effect of the type of cooling agent used during heat treatment and thermal-chemical treatment on the formation of temperature gradient and stress-deformation distribution in cast pallets, which are part of furnace accessories used in this treatment, are disclosed. During operation, pallets are exposed to the effect of the same conditions as the charge they are carrying. Cyclic thermal loads are the main cause of excessive deformations or cracks, which after some time of the cast pallet operation result in its withdrawal due to damage. One of the major causes of this damage are stresses formed under the effect of temperature gradient in the unevenly cooled pallet construction. Studies focused on the analysis of heat flow in a charge-loaded pallet, cooled by various cooling agents characterized by different heat transfer coefficients and temperature. Based on the obtained temperature distribution, the stress distribution and the resulting deformation were examined. The results enabled drawing relevant conclusions about the effect of cooling conditions on stresses formed in the direction of the largest temperature gradient.

Depending on the course of the processes of heat treatment and thermo-chemical treatment, the technological equipment of heat treatment furnaces is exposed to different operating conditions, as the said processes differ among themselves in the temperature of annealing and atmosphere prevailing in the furnace chamber, in the duration of a single work cycle and in the type and temperature of the coolant. These differences affect the magnitude of stresses occurring in each cycle of the operation of furnace accessories, and thus play an important role in fatigue processes leading to the destruction of these accessories. The kinetics of temperature changes during each cooling process plays an important role in the formation of thermal stresses on the cross-section of the cooled parts. It depends on many factors, including the initial cooling temperature, the type and temperature of the cooling medium, or the dimensions and shape of the object. This article presents a numerical analysis of the effect of the initial temperature on the distribution of stresses on the cross-section of the grate ribs, generated in the first few seconds of the cooling process carried out in two cooling media, i.e. hardening oil and water. The analysis was carried out by the finite element method, based on the results of experimental testes of temperature changes in the rib during its cooling.

The purpose of this study was to establish a relationship between the type of wall connection used in the cast grates, which are part of the

equipment operating in furnaces for heat treatment and thermal-chemical treatment, and stresses generated in these grates during the

process of rapid cooling. The places where the grate walls are connected to each other are usually characterized by the thickness larger

than the remaining parts of walls. Temperature variations in those places are responsible for the formation of hot spots, and in the hot spots

temperature changes much more slowly. The type of wall connection shapes the temperature gradient in the joint cross-section, and hence

also the value of thermal stresses generated during cooling. In this study, five different designs of the grates were compared; the difference

in them was the type of the designed wall connection. The following design variants were adopted in the studies: X connections with and

without holes, T connections with and without technological recesses, and R (ring) connection. Numerical analysis was performed to

examine how the distribution of temperature changes in the initial phases of the cooling process. The obtained results served next as a tool

in studies of the stress distribution in individual structures. The analysis were carried out by FEM in Midas NFX 2014 software. Based on

the results obtained, the conclusions were drawn about the impact of different types of wall connections on the formation of thermal

stresses in cast grates.

In this paper, by using a semi-analytical solution based on multi-layered approach, the authors present the solutions of temperature, displacements, and transient thermal stresses in functionally graded circular hollow cylinders subjected to transient thermal boundary conditions. The cylinder has finite length and is subjected to axisymmetric thermal loads. It is assumed that the functionally graded circular hollow cylinder is composed of N fictitious layers and the properties of each layer are assumed to be homogeneous and isotropic. Time variations of the temperature, displacements, and stresses are obtained by employing series solving method for ordinary differential equation, Laplace transform techniques and a numerical Laplace inversion.