The paper describes an integrated laser absorption system as a potential tool for breath analysis for clinical diagnostics, online therapy monitoring and metabolic disorder control. The sensors operate basing on cavity enhanced spectroscopy and multi-pass spectroscopy supported by wavelength modulation spectroscopy. The aspects concerning selection of operational spectral range and minimization of interference are also discussed. Tests results of the constructed devices collected with reference samples of biomarkers are also presented. The obtained data provide an opportunity to analyse applicability of optoelectronic sensors in medical screening.
This article presents the results of a numerical analysis of the road acoustic screen deterioration. Due to the fact that road noise barriers are located in an environment of very high corrosivity, the problem is the rusting of the metal cladding of component panels. The presented case study was, therefore, verified to fulfill the requirements presented in the Eurocode EN 1794-1. Static analysis for wind load and dynamic analysis for the load induced from vehicles was carried out. The analysis presented in the article proved the design errors and their contribution to the formation of severe corrosion, as well as demonstrating the importance of dynamic analysis in the design of acoustic screens.
In recent years, the Budryk Coal Mine (KWK Budryk) reached the mining depth of 1300 m, where there is about 160 million tons of coal, including 120 million tons of coking coal (type 35). The task of the Coal Processing Plant complex modernization was undertaken. The article presents the modernization of coal screening, classification and dewatering systems at the KWK Budryk Processing Plant and the implementation of screening of PROGRESS ECO sp. z o.o. SK. The modernization project defined the following technical requirements for all screens in the KWK Budryk Coal Processing Plant extension project:
- Vibrating screens with a linear type drive with a drive unit placed on the drive beam of the trommel screen in the form of vibration generators;
- Screen drives equipped with a starting-braking device;
- The use of main screen drive bearings with a nominal service life of at least 40,000 man-hours;
- All work surfaces made of materials with a strength of up to 80 mm grain and abrasion resistance; side strips and sieves fixed in a way ensuring trouble-free operation, and at the same time quick and easy replacement;
- Sheets made of stainless steel;
- Side walls, beams and other elements attached to them connected with screws using a system protecting against corrosion and elements separation;
- The use of a work parameters monitoring and visualization system, i.e.
- pitch of the riddle,
- bearing operating temperatures and the condition of their wear.
Three types of screens were provided:
- PWP1-1Z-2,8x6,0 screeners that alternatively perform sieving or desliming processes,
- PWP1-2.4x6.0 screening machines performing desliming processes,
- PWP1-2.0x6.0 screens performing the classification process.
The purpose of this study is to find the value of the discharge coefficient (Cd) on a sieve with a circular perforated plate so that it can be used for application in the field. The method used is to make a physical model test of the screen weir in the laboratory with a width of 40 cm and a length of 797 cm, then the screen is made variations in the diameter of the hole 6, 8, 10 and 12 mm, flowrate Q = 453–4 481 cm3∙s–1 and the slope of the screen θ = 20–45°. The result was quite ef-fective, the sediment did not enter above the screen and did not clog the screen even the catch was quite good about 80% of the screen rods. The discharge coefficient (Cd) is directly proportional to the square value of the number Froude (Fr), the slope of the screen (θ) and the ratio of distance, diameter of the screen (a:d) and inversely proportional to the value of the specific energy square (E). From modelling the average value of the discharge coefficient (Cd) between 0.1–2.75 with NSE = 0.71, MAE = 0 and RMSE = 0.12.
The emergence of solar cells on flexible and bendable substrates has made the printing process a ubiquitous tool for the fabrication of these devices. The various printing techniques available now such as inkjet, screen and flexography offer cost- effectiveness, user-friendliness and suitability for mass production. While downscaling the fill factor and efficiency of organic solar cells. A multilayered structure, the combination of different printing techniques avails the variety of thickness and resolution required for each layer in the production of an organic solar cell. In this review article, we discuss the suitability of the inkjet and screen printing processes to produce organic solar cells. We also discuss various challenges involved in the fabrication of organic solar cells using these two techniques and the possible solutions for the same. We also provide an analogy that both processes share. Further, we consider future possibilities of combining these printing technologies to produce organic solar cells to improve device performance.
Sensing technology has been developed for detection of gases in some environmental, industrial, medical, and scientific applications. The main tasks of these works is to enhance performance of gas sensors taking into account their different applicability and scenarios of operation. This paper presents the descriptions, comparison and recent progress in some existing gas sensing technologies. Detailed introduction to optical sensing methods is presented. In a general way, other kinds of various sensors, such as catalytic, thermal conductivity, electrochemical, semiconductor and surface acoustic wave ones, are also presented. Furthermore, this paper focuses on performance of the optical method in detecting biomarkers in the exhaled air. There are discussed some examination results of the constructed devices. The devices operated on the basis of enhanced cavity and wavelength modulation spectroscopies. The experimental data used for analyzing applicability of these different sensing technologies in medical screening. Several suggestions related to future development are also discussed.
Oil can be produced from reservoirs by use of primary methods that use natural reservoir drive, secondary methods, involving a physical displacement of oil and tertiary (enhanced), in which additional types of energy support oil recovery. About 25-35% of original oil in place for light and medium oil and about 10% heavy oil could be extracted by primary and secondary methods. Injection of CO2 into the oil fields (CO2-EOR) is one of the tertiary oil recovery method. Carbon dioxide is used for increasing oil extraction due to the fact that: to maintain reservoir pressure, reduces the oil viscosity and facilitates its movement in the reservoir, reduces density and increase the volume of oil, interacts with rocks. Depending on the oil composition and the reservoir pressure and temperature injected carbon dioxide can displace oil from the reservoir miscible or immiscible. Additional 10-20% of the oil extraction over primary and secondary methods recovery can be obtained under the miscibility conditions, in immiscibility condition additional oil production is lower. EOR method selection depends on many geological, reservoir and economic parameters. These include: density, viscosity and composition of the oil, minimum miscibility pressure, the recovery factor and vertical and horizontal reservoir variability. Using the above criteria appropriate EOR method for given oil field can be selected. The five parameters: the reservoir depth, the oil density, pressure and temperature of the reservoir is used for the selection of oil fields suitable for miscible oil displacement.
Optoelectronic technology plays an important role in medical diagnosis. In the paper a review of some optoelectronic sensors for invasive and non-invasive human health test is presented. The main attention is paid on their basic operation principle and medical usefulness. The paper presents also own research related to developing of tools for human breath analysis. Breath sample unit and three gaseous biomarkers analyzer employing laser absorption spectroscopy designed for clinical diagnostics were described. The analyzer is equipped with sensors for CO, CH4 and NO detection. The sensors operate using multi-pass spectroscopy with wavelength modulation method (MUPASS-WMS) and cavity enhanced spectroscopy (CEAS).
en
pl
