The paper presents the results of measurements and predictions of radial thrust in centrifugal pump with specific speed ns = 26. In the pump tested, a volute with rectangular cross-section was used. The tests were carried out for several rotational speeds, including speeds above and below the nominal one. Commercial code ANSYS Fluent was used for the calculations. Apart from the predictions of the radial force, the calculations of axial thrust were also conducted, and correlation between thrust and the radial force was found. In the range of the measured rotational speeds, similarity of radial forces was checked.
The paper shows the new method for noise reduction in external gear pumps based on the analysis of the pressure in inter teeth volumes. The simulation model and measurement results of pressure changes in the inter teeth volume has been presented. Based on simulation results an additional volume has been obtained, which is connected to the inter teeth volume (decompression filter volume). Due this additional volume the build down processes in the pump are longer and the pressure overdue in the inter teeth volumes are smaller. This leads to the reduction of the dynamical excitation forces inside the pump and noise, especially in the higher frequency rangeI.
A novel type of an axial, piston-driven high pressure hydraulic pump with variable capacity marks a significant improvement in the area of the hydraulic machinery design. Total discharge from hydrostatic forces eliminates a need for a servomechanism, thus simplifying operation, reducing weight and introducing the possibility of the pump displacement control by computer. PWK-type pumps, invented in the Gdansk University of Technology, offer high efficiency for pressure levels up to 55 MPa, ability to work self sucking even at high speed. However, the heart of the new invention, the commutation unit, creates harmful pressure peaks. Those peaks can be mitigated by the introduction of a compensation chamber with elastic walls. Owing to the dynamic character of events taking place in the pump, a need for computer simulation arouse in order to understand phenomena leading to the occurrence of pressure peaks and choose compensation chamber parameters accordingly. A CFD package alone would not be sufficient to reliably represent the interaction between the compensation chamber wall and the working fluid. This paper presents Fluid Structure Interaction approach comparing 3 different models: 2 simplified models of the pump and a full pump model.
The paper presents the results of hydrogeological parameters determination carried out in the area of the Muschelkalk outcrop (Middle Triassic) near Tarnów Opolski. The studies consisted of a short pumping test in 16 piezometers and then their flooding and observation of water table recovery after the stopping of the pumping. The test allowed the values of hydraulic conductivity and specific capacity of Muschelkalk layers ranging from 8.56 · 10–8 m/s to 3.63 · 10–3 m/s and from 0.0075 to 128 m3/h/1mS, respectively, to be calculated. The wide range of values is related to the fact of studying the layers characterized by high permeability and water-bearing capacity (Karchowice Beds, Diplopora Beds and Górażdże Beds) as well as layers with low permeability (Gogolin Beds). The dense network of the research points made it possible to demonstrate the surface variability of rocks permeability and water- bearing capacity, determined mostly by the direction of outcrops of individual layers. The results of the conducted studies show that the most water-bearing zone of the area is related to the carbonate rocks of the Karchowice, Diplopora and Górażdże Beds, characterized by the highest values of hydraulic conductivity k (above 2 · 10–4 m/s) and specific capacity q (above 15 m3/h/1mS), in the belt stretching latitudinally through Kosorowice–Otmice. The studied area can be considered a Polish limestone-concrete field where several mines exploiting Muschelkalk carbonate rocks operate. The results of the conducted studies may be useful for the correct prognosis of the groundwater inflow either to already existing quarries or newly designed mines within the Major Groundwater Basins.
The unique oasis of Zousfana, on the western edge of the Grand Erg Occidental, Taghit is the pearl of the oases of Saoura, a palm grove of 180 ha over an 18 km length crossed by Oued Zouzfana. It regroups the different types of landscapes of an arid zone (erg, hamada, barga – a small hill, oued ...). Taghit is known for its hydraulic civilization, the oasis in its hostile environment has survived thanks to the exploitation of rare groundwater irrigation according to the traditional customs applied to the whole of society. The peasants spur out the water resources through foggaras and traditional wells. But the intervention of modern irrigation techniques in an anarchic way has disrupted the fragile mode of irrigation and the abandonment of the palm grove. The over-exploitation of groundwater by the use of boreholes and motor pumps leads to the drying up of water sources, mists and traditional wells. Today, only 45 000 palm trees are productive and less than 1500 fruit trees. There are 500 fellahs in the entire agricultural area of Taghit, the majority of them is fleeing work in the oasis because of the lack of income from it. When comparing the results of analyses from different campaigns (2015 and 2008), a spectacular increase in the salt concentrations in the groundwater of the different palm groves is noticed. According to our investigations, the main causes of this jump are: the overexploitation of the water tables by motor pumps, the abandonment of land inside the palm grove, the lack of maintenance of the gardens, the exploitation of domestic wastewater in the irrigation. According to this preliminary study, it is important for the State to make farmers aware of the role of their traditional irrigation systems in the continuity of the oasis and life in it.
The purpose of the work was to experimentally determine the characteristics of the prototype of a Roto-Jet pump (the Pitot tube pump) during its operation under conditions typical for the domestic micro power plant. The low-boiling fluid, sold under the trade name of HFE7100 and characterised by a zero ozone depletion potential (ODP) coefficient, was used as a working medium in the organic Rankine cycle (ORC). An electric thermal oil heater with a maximum power of 2×24 kWe was used as a heat source. The pump of Roto-Jet type was specially designed for the operation with the following rated parameters of the thermodynamic cycle: nominal flow rate of the working fluid 0.17 kg/s, operating pressure 1.2 MPa. The pump was put under load using an expansion valve that simulated the operation of an expansion machine. The article discusses thermodynamic and flow conditions to be met by the pumping engine as well as results of the experimental research. Moreover, the article includes the operational characteristics of the ORC installation and the Roto-Jet pump obtained during the operation with the target working medium – HFE7100. The engineering problems the authors of this article faced when designing and testing the pumping engine prototype are also presented.
Most high-pressure fuel pumps for compression-ignition engines manufactured today are cam driven. These pumps have numerous advantages, such as low energy consumption and limited production costs. However, a problem arising from the nature of the cam mechanism is an unfavorable distribution of forces in the camshaft-plunger-cylinder system of a delivery section. The authors have proposed an innovative pump design that eliminates most of the problems present in conventional solutions. The pump utilizes a gear-based hypocycloid drive. This paper focuses mainly on the strength analysis of the two critical components (countershaft and mount) of the subassembly under the highest load – simulations were carried out for different critical load states. The following procedure of estimating fatigue life was adopted for computations: the operational evolution of stresses will be systematized to the set of amplitude stresses and mean stresses by means of the “Rainflow” method. The results obtained in the work showed that the main factor determining change of stresses was the presence of clearances in the pump mechanism. It has been proved that the values of clearances have a negative influence on the power transmission in particular – their presence results in loads being carried by the countershaft and not by the support inter-operating with it. This may cause frictional wear of teeth, leading to the improper operation of the transmission. The analysis showed that the mount was designed correctly. This facilitates the use of less demanding constructional materials.
In the 21st century the way to increase the efficiency of new sources of energy is directly related with extended exploration of renewable energy. This modern tendency ensures the fuel economy needs to be realized with nature protection. The increasing of new power sources efficiency (cogeneration, trigeneration systems, fuel cells, photovoltaic systems) can be performed by application of solid sorption heat pumps, regrigerators, heat and cold accumulators, heat transformers, natural gas and hydrogen storage systems and efficient heat exchangers.
The main task of mathematical modelling of thermal and flow processes in vertical ground heat exchanger (BHE-Borehole Heat Exchanger) is to determine the unit of borehole depth heat flux obtainable or transferred during the operation of the installation. This assignment is indirectly associated with finding the circulating fluid temperature flowing out from the U-tube at a given inlet temperature of fluid in respect to other operational parameters of the installation.
The paper presents a model of thermal and flow processes in BHE consisting of two analytical models separately-handling processes occurring inside and outside of borehole. A quasi-three-dimensional model formulated by Zeng was used for modelling processes taking place inside the borehole and allowing to determine the temperature of the fluid in the U-tube along the axis of BHE. For modelling processes occurring outside the borehole a model that uses the theory of linear heat source was selected. The coupling parameters for the models are the temperature of the sealing material on the outer wall of the borehole and the average heat flow rate in BHE. Experimental verification of the proposed model was shown in relation to BHE cooperating with a heat pump in real conditions.
The pump performance and occurrence of cavitation directly depends on different operating conditions. To cover a wide range of operation conditions for detecting cavitation in this work, investigations on the effect of various suction valve openings on cavitation in the pump were carried out. In order to analyse various levels of cavitation in different operation conditions, the effect of the decrease in the inlet suction pressure of the centrifugal pump by controlling the inlet suction valve opening was investigated using this experimental setup. Hence, the acoustic and pressure signals under different inlet valve openings and different flow rates, namely, 103, 200, 302 l/min were collected for this purpose. A detailed analysis of the results obtained from the acoustic signal was carried out to predict cavitation in the pump under different operating conditions. Also, the acoustic signal was investigated in time domain through the use of the same statistical features. The FFT technique was used to analyse the acoustic signal in the frequency domain. In addition, in this work an attempt was made to find a relationship between the cavitation and noise characteristics using the acoustic technique for identifying cavitation within a pump.
Cavitation is an essential problem that occurs in all kinds of pumps. This cavitation contributes highly towards the deterioration in the performance of the pump. In industrial applications, it is very vital to detect and decrease the effect of the cavitation in pumps. Using different techniques to analysis and diagnose cavitation leads to increase in the reliability of cavitation detection. The use of various techniques such as vibration and acoustic analyses can provide a more robust detection of cavitation within the pump. In this work therefore, focus is put on detecting and diagnosing the cavitation phenomenon within a centrifugal pump using vibration and acoustic techniques. The results obtained from vibration and acoustic signals in time and frequency domains were analysed in order to achieve better understanding regarding detection of cavitation within a pump. The effect of different operating conditions related to the cavitation was investigated in this work using different statistical features in time domain analysis (TDA). Moreover, Fast Fourier Transform (FFT) technique for frequency domain analysis (FDA) was also applied. Furthermore, the comparison and evaluation system among different techniques to find an adequate technique incorporating for accuracy and to increase the reliability of detection and diagnosing different levels of cavitation within a centrifugal pump were also investigated.
The purpose of this work is to design and determine the performance of a prototype centrifugal pump impeller for an organic Rankine cycle (ORC) power plant of maximum power 100 kW. The centrifugal pump is especially designed to work on the same shaft as the corresponding ORC microturbine. The ORC unit works on R7100 (HFE7100) – a lowboiling fluid characterized by a zero ozone depletion potential coefficient. The pump has the following rated parameters: nominal flow rate of working fluid 4 kg/s, operating rotor speed 10 000 rpm. The pump designed by means of the 0D meanline method is subject to computational fluid dynamics (CFD) calculations and analysis. The obtained flow field results are discussed and performance characteristics of the pump are presented. The non-cavitating operational region is determined for the pump.
en
pl
