The main objective of this study was to evaluate the intensity and character of the inflammatory reaction caused by an innovative polyester-polyurethane vascular prosthesis implanted into the abdominal aorta of 9 Beagle dogs aged 1-3 years. At 6 and 12 months post implantation the prostheses were removed and tissues samples were examined using 2 methods: histology and immunohistochemistry (IHC). Histology slides stained with hematoxylin and eosin (H&E) were evaluated for the intensity of inflammation by observing the density of inflammatory cells and graded 1 to 4 (1- light inflammation, 4 – severe inflammation). The pro-inflammatory mediator tumor necrosis factor-alpha (TNFα) and two anti-inflammatory mediators, interleukin 1 receptor antagonist (IL1ra), and interleukin 10 (IL10), were also assessed in the tissue samples by IHC methods. Mean (n=5) inflammation grade in H&E slides at 6 months post-implantation (6Mpost) was 2 and mean (n=4) inflammation grade at 12 months (12Mpost) was almost 3. IHC staining showed that TNFα and IL1ra in tissue samples obtained from 6Mpost dogs were expressed at the same intensity indicating equal pro- and anti-inflammatory cytokine levels. However, in the 12Mpost tissues TNFα was expressed more intensely than IL1ra and IL10. Moreover, in 2 dogs at 12Mpost, there were signs of infection assessed on the basis of neutrophil infiltration in the prostheses. In conclusion, the assessment of pro-inflammatory mediators such as TNFα and anti-inflammatory mediators, such as IL1ra and IL10, can help to interpret the intensity of the inflammatory process directed at synthetic prostheses.

The study discusses an experimental method for treatment of high strength domestic sewage on biofilters filled with polyurethane (PUR) waste in the form of trims of upholstery foam. We determined effectiveness of two biological preparations containing effective microorganisms in elimination of organic and biogenic compounds, indicator bacteria and total suspended solids from the sewage pretreated in a septic tank. After four months of work under a hydraulic loading of 76.4 mm∙d ^-1 we found the filter with 60 cm foam layer to be the most efficient in the elimination of BOD ₅, COD _Cr, NH ₄ ⁺-N and coliform bacteria. An average reduction in these pollutants reached 79.4%, 67.8%, 58.0% and 88.0%, respectively. Vertical filters filled with trims of upholstery foam and supplied with effective microorganisms ensured favorable conditions for development of heterotrophic and nitrifying bacteria without any need for additional aeration.

Following paper is focused on experimental and numerical studies of the behavior and energy absorption for both: quasi-static and dynamic axial crushing of thin-walled cylindrical tubes filled with foam. The experiments were conducted on single walled and double walled tubes. Unfilled profiles were compared with tubes filled with various density polyurethane foam. All experiments were done in order to possibility of the safety of the elements absorbing collision energy which can applied in car body. The dynamic nonlinear simulations were carried out by means of PAM-CRASH™ explicit code, which is dedicated calculation package to modelling of crush. Computational crushing force, plastic hinges locations and specimens post-crushed geometry found to be convergent with the real experiments results. Conducted experiments allowed to draw conclusion, that crashworthiness ability is directly proportional to foam density. The investigation of the experimental data revealed, that double walled tubes have greater energy absorbing ability. A proposed investigation enable to analyze and chosen of optimal parameters of these elements, which can use in automotive industry as an absorption energy components.

The results from the experimental research are presented in the abstract. The experimental research involved utilization of the sludge from the mine water treatment plant of Coal Quarry ČSA/Czechoslovak Army/ (hereinafter “ČSA”) and Coal Quarry Jana Švermy (hereinafter “JŠ”) in the segment of thermal insulation mortars. The mine water treatment is described below including chemical and mineralogical sludge composition as the additional component of the binding material in the polyurethane thermal insulation mortars. Furthermore the composition of experimental mixtures of the thermal insulation polyurethane mortar is presented in the work and its physical-mechanical properties. The monitored elements included the strength characteristics, heat conductivity coefficient λ, and water vapour diffusion coefficient μ.

The paper discusses the use of multiclustering statistical analysis in the assessment of domestic wastewater filtration effectiveness. Calculations included data collected over four months of experiments with using waste as filling material of vertical flow filters for domestic sewage treatment. The effectiveness of pollutants removal was analysed in case of me-chanically shredded waste in the form of PET flakes, PUR foam trims, shredded rubber tires and wadding. The organic compounds (CODcr, BOD5) removal, suspend solids, biogens (as NH4+, PO43– ions) and oxygen saturation changing com-pared with sand filling was analysed. Multiclustering statistical analysis allowed to divide pollutants removal efficiency of analysed materials into 3 clusters, depending on the hydraulic loading. The first group consisted in quality parameters of treated sewage: the highest reduction of BOD5 and NH4-N. It included the values of quality parameters and indicators for the filtrates obtained at the lowest hydraulic load from columns filled with 60 cm of rubber tires or sand. The second group comprised the results for fillings containing foam, PET and rubber tires (the other hydraulic loads).It featured the highest reduction of total suspended solids and PO43–. Removal of easily biodegradable organic compounds was at a similar level in both cluster groups. The filter filled with polyester waste (wadding), which was as effective as 30 cm layer of sand, and the filters filled with 60 cm of sand working at the highest hydraulic load. Third group showed the lowest values of parameters and indicators for analysed filtrates.

Titanium nitride (TiN) is regarded as a potential biomaterial for blood-contact applications. TiN thin films were fabricated by pulsed

laser deposition with the Nd:YAG laser on biologically applied polyurethane. Transmission electron microscopy (TEM) study of 250 nm thick films revealed columnar structure. Such films were observed to be brittle, which led to crack formation and secondary nucleation of microcolumn. TEM studies showed a kinetic mechanism of growth (columnar) in films of 250 nm thickness. It was stated that thinner films were much smoother and uniform than the thicker ones, which could be associated with the surface diffusion mechanism to appear. In order to improve the coatings elasticity, the thickness was reduced to 50 nm, which limited the deposition mechanism operation to the early stage. TEM cross-section observation revealed elastic properties of thin films. A biological test showed that TiN surface film produced on polyurethane is characterized by good biocompatibility and decreased surface affinity for cell adhesion. Films of 0.25 and 0.5 1m thick of TiN were selected for theoretical finite element modelling (FEM) using ADINA program. The micro cracks formation predicted in simulation was verified by phenomena observed in microstructure examinations.

The aim of this research was to develop a composite material to be used as an elastomeric core of the artificial intervertebral disc. Two types of polyurethane composites with non-modified SiO2 and SiO2 modified NH2 group were obtained. The composites made of these materials have different filler content. The effect of modifying fillers for the structure and properties of these materials were investigated.

The study aimed to produce nano- and microfibrous materials from polyurethane (ChronoFlex®C75A/ C75D in 1,1,1,3,3,3–hexafluoro–2–propanol) by solution blow spinning. Experiments were carried out in order to determine the impact of solution blow spinning parameters on fibre diameter and quality of produced materials. The following properties of produced fibre scaffolds were investigated: fibre size, porosity and pore size, wettability, and mechanical properties. The results confirmed that produced nano- and microfibrous materials could be potentially used as scaffolds in three-dimensional cell and tissue cultures.

Considering the environmental pollution caused by waste rubber, some measures should be taken to improve the utilization rate of waste rubber. In this study, the effect of Ethylene Propylene Diene Monomer (EPDM) particles in the polyurethane (PU) foams on sound absorption behavior is investigated for improving sound environment within vehicles and reducing the environment pollution. EPDM of different contents and hardness are used as fillers for producing foams with different pore morphologies and sound absorption properties. The results show adds EPDM to foam would produce smaller pores, higher density and bigger air-flow resistivity. Simultaneously, there are better sound absorption properties of the PU foam composites in the medium frequency region and the better value can be obtained at the lower frequency with the content of EPDM increasing. The hardness of EPDM also shows better influence on sound absorption properties, especially in the medium frequency region. It means the foam pore morphologies have influence on sound absorption properties.