Prof. Małgorzata Kossut of the Nencki Institute of Experimental Biology talks about brain plasticity, the mechanisms of learning, and the mysteries of forgetfulness.
The paper presents research results on the selection of parameters for the asymmetric rolling process of bimetallic plates 10CrMo9-10 + X2CrNiMo17-12-2. They consisted in determining the optimum parameters of the process, which would be ensured to obtain straight bands. Such deformation method introduces in the band the deformations resulting from shear stress, which affect changes in the microstructure. But their effect on the structure is more complicated than in the case of homogeneous materials. It has been shown that the introduction of asymmetric conditions into the rolling process results in greater grain refinement in the so-called hard layer. There was no negative effect on the structural changes in the soft layer observed.
2-phase composites are often used for high demanding parts that can undergo impact loads. However, most of the papers on dynamic loading concerns layered composites. In our opinion, the impact loads are not considered thoroughly enough. Good examples of 2-phase composites are: (1) a WC/Co cermet or (2) a monolithic ceramic Al2O3/ZrO2. The WC/Co cermet is often modelled as having ductile elasto-plastic Co matrix and ideally elastic WC grains. It is because of very high crushing resistivity of the WC.
In this paper, we present an extension to earlier elaborated models ([44]) with the assumption of ideal elasticity of the grains. The new and general numerical model for high-velocity impact of the 2-phase composites is proposed. The idea of this novelty relies on the introduction of crushability of grains in the composite and thermo-mechanical coupling. The model allows for description of the dynamic response both composite polycrystals made of: (1) 2 different purely elastic phases (e.g. Al2O3/ZrO2) or (2) one elastic phase and the second one plastic (e.g. cermet WC/Co), or (3) 2 elasto-plastic phases with different material properties and damage processes. In particular, the analysis was limited to the cases (2) and (3), i.e. we investigated the WC/Co polycrystal that impacted a rigid wall with the initial velocity equal to 50 m/s.
The paper presents the properties of plastics under the trade names of PMMA and Midas, and of Formowax, Romocast 305 and Romocast 930 casting waxes. Their effect on the quality of foundry patterns used in the manufacture of ceramic moulds for precision casting is also discussed. From the selected materials for foundry patterns, samples were made for testing using the following methods: (i) 3D printing in the case of plastics, and (ii) conventional method based on tooling in the form of metal moulds (dies) in the case of casting waxes.
The most important physico-mechanical properties of materials for foundry patterns were determined, i.e. linear shrinkage, softening temperature, relative elongation and coefficient of thermal linear expansion. Bending tests were carried out on samples of patterns printed and made in metal moulds, including determination of the surface roughness of patterns.
After the process of melting out patterns from the cavities of ceramic moulds in an autoclave, the degree of their melting out was visually assessed (i.e. the residues from pattern removal were evaluated). The ash content after burning out of foundry patterns was also determined. The conducted tests allowed comparing the important parameters of materials used for foundry patterns and assessing the suitability of selected plastics as a material for foundry patterns used in the manufacture of high-quality precision castings.
This study was undertaken to investigate the effect of severe plastic deformation (SPD) by extrusion combined with reversible torsion (KoBo) method on microstructure and mechanical properties of Al-5Cu and Al-25Cu alloys. The extrusion combined with reversible torsion was carried out using reduction coefficient of λ = 30 and λ = 98. In this work, the microstructure was characterized by light microscopy (LM), scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM). Compression test and tensile test were performed for deformed alloys. The binary Al-5Cu and Al-25Cu alloys consist of the face cantered cubic (FCC) α phase in the form of dendrites and tetragonal (C16) θ-Al2Cu intermetallic phase observed in interdentritic regions. The increase of Cu content leads to increase of interdentritic regions. The microstructure of the alloys is refined after applying KoB deformation with λ = 30 and λ = 98. Ultimate Tensile Strength (UTS) of Al-5Cu alloy after KoBo deformation with λ = 30 and λ = 98 reached about 200 MPa. UTS for samples of Al-25Cu with λ = 30 and λ = 98 increased compared to Al-5Cu alloy and exceed 320 MPa and 270 MPa respectively. All samples showed increase of plasticity with increase of reduction coefficient. Independently of reduction coefficient, the compressive strain of Al-5Cu alloys is about 60%. The Al-25Cu alloy with λ = 98 showed the value of compressive strain exceed 60%, although for this same alloy but with λ = 30, the compressive strain is only 35%.
This paper presents the results of experimental studies and numerical simulations of the ratcheting for the PA6 aluminum. In the initial determination of the material hardening parameters, the samples were subjected to the symmetrical strain-controlled cyclic tension-compression test. The experimental stress-strain curve was compared with the numerical one obtained for non-linear Frederick-Armstrong and Voce models. For better fitting of both curves, the optimization procedure based on the least-square method and the fuzzy logic was applied. After establishing the hardening parameters, numerical simulations of the ratcheting were made. The boundary value problem was solved by means of discrete analysis. The data (force and displacement) obtained in numerical computations were used to control the ratchetting experiment. The results of experiments and numerical calculations were compared. Good convergence proves the reliability of the determination of material hardening data.
en
pl
