Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 6
items per page: 25 50 75
Sort by:
Download PDF Download RIS Download Bibtex

Abstract

Micro-defects detection in solidified castings of aluminum alloy has always been a hot topic, and the method employed is mainly depends upon the size and shape of the specimens. In present paper, the amount and distribution characters of micro-defects in a series of 2219 aluminum alloy ingot, with diameters of φ1380 mm, φ1250 mm, φ1000 mm, φ850 mm and φ630 mm, prepared by direct chill casting were investigated by means of metallographic, respectively. Samples were cut along the radius direction from slices in the steady casting stage. The result reveals that typical micro-defects are consist of inclusions, porosity and shrinkage under optical microscope, and the total amount of micro-defect per unit area in an ingot slightly decreased with the increase of its diameter. Meanwhile, defects were classified into 2 types according to its size, the results suggesting that defects greater than 40 μm account for the largest proportion among the counted two kinds of defects. Moreover, the distribution of defects greater than 40 μm along the radial direction was detected, its amount increases as its distance from the side, indicating that the micro-defects greater than 40 μm distributed the most in the center zone of ingots and the larger the ingot diameter, the more obvious the tendency was.

Go to article

Authors and Affiliations

Yu Liu
Yuanchun Huang
Zhengbing Xiao
Download PDF Download RIS Download Bibtex

Abstract

The paper is concerned with comparing the methods for determining the ferrite content in castings from duplex stainless steels. It uses Schaeffler diagram, empirical formula based calculation, image analysis of metallographic sample, X-ray diffraction and measurement with a feritscope. The influence of wall thickness of the casting on the ferrite content was tested too. The results of the experiments show that the casting thickness of 25 or 60 mm does not have a significant effect on the measured amount of ferrite. The image analysis of metallographic sample and the measurement with the feritscope appear to be the most suitable methods. On the contrary, predictive methods, such as Schaeffler diagram or empirical formula based calculation are only indicative and cannot replace the real measurements. X-ray diffraction seems to be the least suitable measuring method. Values of ferrite content measured in such a way often deviated from the values measured by image analysis and with feritscope.

Go to article

Authors and Affiliations

V. Kaňa
V. Pernica
A. Zadera
V. Krutiš
Download PDF Download RIS Download Bibtex

Abstract

Casting porosity is the main factor influencing the fatigue properties of Al-Si alloys. Due to the increasing use of aluminum castings, porosity characterization is useful for estimating their fatigue strength. In principle, a combination of metallographic techniques and statistical pore analysis is a suitable approach for predicting the largest defect size that is critical for the casting. Here, the influence of modifiers and casting technology on the largest pore size population in AlSi7Mg alloy specimens is obtained and discussed adopting the Murakami's approach. However, porosity evaluation is a challenge in the case of microshrinkage pores, which are frequently found in industrial castings. Their complicated morphology prevents a reliable definition of an equivalent defect size based on metallographic techniques. This contribution reports the application of X-ray tomography to the 3D reconstruction of real pores in cast Al-Si alloys and provides insight into the complication of microshrinkage pore sizing by metallography.

Go to article

Authors and Affiliations

Stanislava Fintová
Giancarlo Anzelotti
Radomila Konečná
Gianni Nicoletto
Download PDF Download RIS Download Bibtex

Abstract

Article presents results of laser overlaying welding of metal powder Inconel 625. Laser metal deposition by laser engineered net shaping (LENS) is modern manufacturing process for low scale production series. High alloy materials such as Inconel 625 nickel based super alloy have high thermal resistant and good mechanical properties, nevertheless it's hard to machining. Plastic forming of high alloy materials such as Inconel 625 are difficult. Due to high strength characteristic performing components made from Inconel alloy are complex, selective melting of metallic powder using laser beam are alternative method for Inconel tooling. Paper present research of additive deposition of spatial structure made from Inconel 625 metallic powder with CO2 laser and integrated powder feeder. Microstructure analysis as well as strength characteristic in normal condition and at elevated temperature was performed. Possibility of using LENS technology for manufacturing components dedicated for work in high temperature conditions are presented.

Go to article

Authors and Affiliations

H. Danielewski
B. Antoszewski
Download PDF Download RIS Download Bibtex

Abstract

Paper presents results of laser welding of dissimilar joints. Flange pipe joints of austenitic TP347-HFG and low carbon S235JR steels were performed. Possibility of laser girth welding of dissimilar joints was presented. Welding of dissimilar materials are complex phenomena, chemical composition of chromium and nickel base austenitic steel with carbon amount of 0.07%, comparing to low carbon steel with trace amount of chromium, nickel and with 0.17% of carbon are different, and affect on welding result. Amount of carbon and chromium have great effect on steel phase transformation and crystallization process, which affect on material hardenability and strength characteristic. In conventional GMA welding methods solidification process of different metals is controlled by use of a selected filler material, for creating buffer zone. The main advantages of laser welding over other methods is process without an additional material, nevertheless some application may require its use. Laser welding with additional material combines advantages of both methods. To carry out weld with high strength characteristic, without welding defects, selecting chemical composition of filler wire are required. Welding parameters was obtained using numerical simulation based on Finite Element Method (FEM). Joint properties was investigated using hardness test. Metallographic analysis of obtained weld was carried out using optical microscopy and energy dispersive spectroscopy (EDS) analysis.

Go to article

Authors and Affiliations

H. Danielewski
A. Skrzypczyk
K. Mulczyk
A. Zrak
Download PDF Download RIS Download Bibtex

Abstract

The research focused on the influence of the solution temperature on the structure of precipitation hardening multi-component hypoeutectic aluminium alloys. The AlSi8Cu3 and AlSi6Cu4 alloys were used in the study and were subjected to a thermal-derivative analysis. The chemical composition and crystallization of phases and eutectics shift the characteristic points and the corresponding temperatures to other values, which affect to, for instance, the solution temperature. The alloys were supersaturated at 475°C (according to the determined temperature (TSol) and 505°C for 1.5 hours. Aging was performed at 180°C for 5 hours. The Rockwell hardness measurement, metallographic analysis of alloys by means of light microscopy as well as chemical and phase analysis using scanning electron microscopy and X-ray crystallography were carried out on alloys. The use of computer image analysis enabled the determination of the amount of the current Al2Cu phase in the alloys before and after heat treatment.

Go to article

Authors and Affiliations

P.E. Smolarczyk
M. Krupiński

This page uses 'cookies'. Learn more