This paper presents the results of experimental testing of parameters of the flow of an agitated liquid in a stirred tank with an eccentrically positioned shaft and with a Rushton turbine. The investigations were focused on the impact of the stirrer shaft shift in relation to the stirred tank vertical axis on the agitated liquid mean velocities and the liquid turbulent velocity fluctuations, as well as on the turbulence intensity in the tank. All the experiments were carried out in a stirred tank with the inner diameter of 286 mm and a flat bottom. The adopted values of the shaft eccentricity were zero (central position) and half the tank radius. The liquid flow instantaneous velocities were measured using laser Doppler anemometry.
The optimization of finned tube heat exchanger is presented focusing on different fluid velocities and the consideration of aerodynamic configuration of the fin. It is reasonable to expect an influence of fin profile on the fluid streamline direction. In the cross-flow heat exchanger, the air streams are not heated and cooled evenly. The fin and tube geometry affects the flow direction and influences temperature changes. The heat transfer conditions are modified by changing the distribution of fluid mass flow. The fin profile impact also depends on the air velocity value. Three-dimensional models are developed to find heat transfer characteristics between a finned tube and the air for different air velocities and fin shapes. Mass flow weighted average temperatures of air volume flow rate are calculated in the outlet section and compared for different fin/tube shapes in order to optimize heat transfer between the fin material and air during the air flow in the cross flow heat exchanger.
Nowadays, the energy cost is very high and this problem is carried out to seek techniques for improvement of the aerothermal and thermal (heat flow) systems performances in different technical applications. The transient and steady-state techniques with liquid crystals for the surface temperature and heat transfer coefficient or Nusselt number distribution measurements have been developed. The flow pattern produced by transverse vortex generators (ribs) and other fluid obstacles (e.g. turbine blades) was visualized using liquid crystals (Liquid Crystal Thermography) in combination with the true-colour image processing as well as planar beam of double-impulse laser tailored by a cylindrical lens and oil particles (particle image velocimetry or laser anemometry). Experiments using both research tools were performed at Gdańsk University of Technology, Faculty of Mechanical Engineering. Present work provides selected results obtained during this research.
The work deals with experimental and numerical thermodynamic analyses of cross-flow finned tube heat exchangers of the gas-liquid type. The aim of the work is to determine an impact of the gas non-uniform inlet on the heat exchangers performance. The measurements have been carried out on a special testing rig and own numerical code has been used for numerical simulations. Analysis of the experimental and numerical results has shown that the range of the non-uniform air inlet to the considered heat exchangers may be significant and it can significantly affect the heat exchanger efficiency.
Cu–4.7 wt. % Sn alloy wire with Ø10 mm was prepared by two-phase zone continuous casting technology, and the temperature field, heat
and fluid flow were investigated by the numerical simulated method. As the melting temperature, mold temperature, continuous casting
speed and cooling water temperature is 1200 °C, 1040 °C, 20 mm/min and 18 °C, respectively, the alloy temperature in the mold is in the
range of 720 °C–1081 °C, and the solid/liquid interface is in the mold. In the center of the mold, the heat flow direction is vertically
downward. At the upper wall of the mold, the heat flow direction is obliquely downward and deflects toward the mold, and at the lower
wall of the mold, the heat flow deflects toward the alloy. There is a complex circular flow in the mold. Liquid alloy flows downward along
the wall of the mold and flows upward in the center.
In this research work, the Ti-6Al-4V material was used for the investigation of machining parameters by means of hybrid micro electrical discharge machining to improve the machining process and reduce the negative effects of debris accumulation in the drilled hole. L9 orthogonal array was used in the Taguchi based grey relational analysis to optimize the parameters such as material removal rate and diametrical accuracy of the machining process for Ti-6Al-4V. This work encompasses the design, development, and calibration of the work piece vibration platform and experimental analysis of the process parameters by means of the hybrid micro electrical discharge machining process. The maximum material removal rate and minimum surface roughness was observed at the current value of 2.5 A, pulse on time is 2 µs and pulse off time is 14.5 µs. The maximum material removal rate was observed for the increase in pulse on time with 14.4 µs and 4 A current level. The diametrical accuracy of the microholes was increased while increasing the pulse off time and decreasing the pulse on time. The fluid flow simulation has been conducted to find out the pressure drop and to know the velocity of the flow inside the hole for the effective flushing of the debris during machining.
For a deeper understanding of the inner ear dynamics, a Finite-Element model of the human cochlea is developed. To describe the unsteady, viscous creeping flow of the liquid, a pressure-displacement-based Finite-Element formulation is used. This allows one to efficiently compute the basilar membrane vibrations resulting from the fluid-structure interaction leading to hearing nerve stimulation. The results show the formation of a travelingwave on the basilar membrane propagating with decreasing velocity towards the peaking at a frequency dependent position. This tonotopic behavior allows the brain to distinguish between sounds of different frequencies. Additionally, not only the middle ear, but also the transfer behavior of the cochlea contributes to the frequency dependence of the auditory threshold. Furthermore, the fluid velocity and pressure fields show the effect of viscous damping forces and allow us to deeper understand the formation of the pressure difference, responsible to excite the basilar membrane.
en
pl
