In this work, the design of current mode Fractional order filter using VDTAs (Voltage differencing trans-conductance amplifier) as an active element with grounded capacitors has been proposed. The approximate transfer functions of low and high pass filters of fractional order on the basis of the integer order transfer has been shown and the form of those functions of filters is also implemented using VDTA as an active building block. In this work, filters of the different sequence have been realized. The frequency domain simulation results of the proposed filters are obtained on Matlab and PSPICE with TSMC CMOS 180 nm technology parameters. Stability and sensitivity is also verified.

Various components of surface texture are identified, namely form, waviness and roughness. Separation of these components is done by digital filtering. Several problems exist during analysis of two-process surfaces. Therefore the Gaussian robust profile filtering technique was established and has been studied here. The computer generated 2D profiles and 3D surface topographies having triangular scratches as well as measured stratified surfaces were subjected to filtration. However even robust filter applications cause distortion of profiles having valleys wider than 100 μm. In order to minimize the distortion associated with wide and deep valleys, the robust filter should be modified. A special procedure was elaborated for minimizing distortion of roughness profiles caused by filtration. Application of this method to analyses of several profiles was presented. The difference between 1-D and 2-D filtering of surface topography using the same kind of filter was discussed. As a result we found that modification of a 2-D surface topography filter was not necessary.

Over the last twenty years, there has been a growing interest in the design of tunable devices at microwave frequencies by us- ing liquid crystals technology. In particular, the use of liquid crystals with high dielectric anisotropy allows manufacturing voltage-controlled devices to operate in a wide frequency range. In this work the frequency response of a liquid crystal band-pass filter with dual-mode microstrip structure has been studied in depth by using a simulation software tool. A reshap- ing of a conventional dual-mode square patch resonator bandpass filter with a square notch, studied in the literature, has been proposed with the goal of improving the filter performance. The main features achieved are a significant increase in the return loss of the filter and a narrowing of a 3-dB bandwidth. Specifically, a reduction in the filter bandwidth from 800 MHz to 600 MHz, which leads to a return loss increase from 6 dB to 12.5 dB, has been achieved. The filter centre frequency can be tuned from 4.54 GHz to 5.19 GHz.

The influence of wrong information about transition and measurement models on estimation quality has been presented in the paper. Two methods of a particle filter, with and without the Population Monte Carlo modification, and also the extended and unscented Kalman filters methods have been compared. A small 5-bus power system has been used in simulations, which have been performed based on one data set, and this data set has been chosen from among 100 different – to draw the most general conclusions. Based on the obtained results it has been found that for the particle filter methods the implementation of the slightly higher standard deviation than the true value, usually increases the estimation quality. For the Kalman filters methods it has been concluded that optimal values of variances are equal to the true values.

Single-branch filters are still popular and are commonly used for power quality improvement purposes. Analysis of a single-branch filter is a relatively simple task. Although individual filters tuned to specific harmonics can be easily designed, after connecting them into a group it turns out that the capacitance and inductance mutually influence each other, distorting the resulting frequency characteristics. This article presents a matrix method for design a group of single-branch filters, so that the resultant frequency characteristic satisfies the design requirements including the requirements for location of the frequency characteristic maxima. Designer indicates the frequencies of the parallel resonances.

Hybrid filter material was obtained via modification of polypropylene (PP) nonwoven with nanosize zinc oxide particles of a high aspect ratio. Modification was conducted as a three-step process, a variant of hydrothermal method used for synthesis of nano-ZnO, adopted for coating three dimensional polymeric nonwoven filters. The process consisted of plasma treatment of nonwoven to increase its wettability, deposition of ZnO nanoparticles and low temperature hydrothermal growth of ZnO rods. The modified nonwovens were investigated by a high resolution scanning electron microscopy (HR-SEM). It has been found that the obtained hybrid filters offer a higher filtration efficiency, in particular for so called most penetrating particle sizes.

Trials of cast steel filtration using two types of newly-developed foam filters in which carbon was the phase binding ceramic particles have

been conducted. In one of the filters the source of carbon was flake graphite and coal-tar pitch, while in the other one graphite was

replaced by a cheaper carbon precursor. The newly-developed filters are fired at 1000o

C, i.e. at a much lower temperature than the

currently applied ZrO2-based filters. During filtration trials the filters were subjected to the attack of a flowing metal stream having

a temperature of 1650°C for 30 seconds.

Characteristic of the filters’ properties before and after the filtration trial were done. It was found, that the surface reaction of the filter

walls with molten metal, which resulted in local changes of the microstructure and phase composition, did not affect on expected filter

lifetime and filtration did not cause secondary contamination of cast steel.

The paper deals with the basic set-up of single-frequency microchip laser - so called Lyot filter configuration. Description of its operation and practical realization is given. Some results obtained for Nd:YAG/KTP microchip laser are presented. The evidences of single-frequency operation and its limits are emphasized. Described construction constitutes the base for building the frequency stabilization of green 532 nm microchip laser.

An LLCL-filter is becoming more attractive than an LCL-filter as the interface between the grid-tied inverter and the grid due to possibility of reducing the copper and the magnetic materials. The efficiency of the LLCL-filter based single-phase grid-tied inverter also excites interests for many applications. The operation of the switches of the VSI is various with different modulation methods, which lead to different efficiencies for such a single-phase grid-tied inverter system, and therefore important research has been carried out on the effect of the choice of PWM schemes. Then power losses and efficiencies of the LLCL-filter and the LCL-filter based single-phase grid-tied inverters are analyzed and compared under the discontinuous unipolar, the dual-buck and the bipolar modulations. Results show that the efficiency of LLCL-filter based inverter system is higher than the LCL- filter based independent on the modulation method adopted. Experiments on a 2 kW prototype are in good agreement with results of the theoretical analysis.

The paper presents the equalization problem of non-linear phase response of digital IIR type filters. An improved analytical method of designing a low-order equalizer is presented. The proposed approach is compared with the original method. The genetic algorithm is presented as an iterative method of optimization. The vector and matrix representation of the all-pass equalizer are shown and introduced to the algorithm. The results are compared with the analytical method. In this paper we have also proposed the use of an aging factor and setting the initial population of the genetic algorithm around the solution provided by the analytical methodology

In this paper, the sensitivity analysis of the elliptic filters realized by using biquadratic structures was carried out. The influence

of spread the structure parameter values on the shape of the frequency characteristic of the filter transmittance modulus was analyzed. The analysis was limited to the case of even order low-pass filter. Defining the proper class of the sensitivity coefficients, the changes influence of individual structure parameters on the deviation of basic parameter values of the characteristic was considered. The considerations were illustrated by the numerical example.

As a result of the development of modern vehicles, even higher accuracy standards are demanded. As known, Inertial Navigation Systems have an intrinsic increasing error which is the main reason of using integrating navigation systems, where some other sources of measurements are utilized, such as barometric altimeter due to its high accuracy in short times of interval. Using a Robust Kalman Filter (RKF), error measurements are absorbed when a Fault Tolerant Altimeter is implemented. During simulations, in order to test the Nonlinear RKF algorithm, two kind of measurement malfunction scenarios have been taken into consideration; continuous bias and measurement noise increment. Under the light of the results, some recommendations are proposed when integrated altimeters are used.

In this paper, we show that signal sampling operation can be considered as a kind of all-pass filtering in the time domain, when the Nyquist frequency is larger or equal to the maximal frequency in the spectrum of a signal sampled. We demonstrate that this seemingly obvious observation has wideranging implications. They are discussed here in detail. Furthermore, we discuss also signal shaping effects that occur in the case of signal under-sampling. That is, when the Nyquist frequency is smaller than the maximal frequency in the spectrum of a signal sampled. Further, we explain the mechanism of a specific signal distortion that arises under these circumstances. We call it the signal shaping, not the signal aliasing, because of many reasons discussed throughout this paper. Mainly however because of the fact that the operation behind it, called also the signal shaping here, is not a filtering in a usual sense. And, it is shown that this kind of shaping depends upon the sampling phase. Furthermore, formulated in other words, this operation can be viewed as a one which shapes the signal and performs the low-pass filtering of it at the same time. Also, an interesting relation connecting the Fourier transform of a signal filtered with the use of an ideal low-pass filter having the cut frequency lying in the region of under-sampling with the Fourier transforms of its two under-sampled versions is derived. This relation is presented in the time domain, too.

Commonly known DC-AC switching converters are commonly used in compensator branches. One example of this is a static synchronous compensator (STATCOM). It consists of a voltage source converter (VSC) and acts as an inverter with a capacitor as a DC power source. These compensators use the PWM switching scheme or space vector modulation (SVM) method. Both methods require the desired signal to be generated. In some cases, as during the synthesis of self-excited systems or active energy-compensators, it is necessary to perform the desired branch immittance, e.g. negative capacitance, inductance, resistance or irrational impedance. In such cases, it is necessary to control the universal branch on the basis of a formula. This article presents the implementation method for the convolutional type impedance operators.