This paper deals with the experimental validation of the suitability of the method for measuring radial variations of components on the process tool. The tests were conducted using a computerized PSA6, which was compared to a Talyrond 73. The results of measurement of roundness deviations as well as roundness profiles were analyzed for a sample of 70 shafts. The roundness deviations were assessed by determining the experimental errors, while the profiles obtained with the tested device were compared to those registered by the reference device using three correlation coefficients.

The paper presents the results of experimental investigations into variations of the stress tensor components due to both the interaction between subsurface fatigue crack faces and rolling contact. The load assumed represents real interaction between the railway wheel and rail. The Grating Holographic Interferometry (GHI) method was employed. The results obtained were compared with those resulting from numerical simulations performed using FEM. The results reveal a strong influence exerted by shape, crack thickness distribution and roughness of the crack faces, respectively, on the distribution of displacement and stress tensor component fields. A new concept consisting in application of the effective crack thickness was proposed. The best agreement between experimental and numerical results was achieved in the case when the real crack shape, effective crack thickness and the friction coefficient of 0.3 were assumed.

In the paper, the authors discuss the numerical and experimental modal analysis of the cantilever thin-walled beams made of a carbon-epoxy laminate. Two types of beams were considered: circumferentially asymmetric stiffness (i.e., CAS) and circumferentially uniform stiffness (i.e., CUS) beams. The layer-up configurations of the laminate were chosen to get a vibration mode coupling effect in both analysed cases. The aim of the paper was to perform the numerical and experimental modal analysis of the composite structures, when a flapwise bending with torsion coupling effect or flapwise-chordwise bending coupling effect took place. Firstly, numerical studies by the finite element method was performed. The numerical simulations were carried out by the Lanczos method in the Abaqus software package. The natural frequencies and the corresponding free vibration modes were determined. Next, the experimental modal analyses of the CAS and CUS beams were performed. The test stand was consisted of a special grip, two beams with an adhered holder, the LMS Scadas III system with a modal hammer and an acceleration sensor. Finally, the results of both methods were compared.

In this paper, an experimental method was utilized to investigate acoustic emission (AE) characteristics and to identify emission sources of the nonlinear AE signal on the cylinder body of a large low-speed two-stroke marine diesel engine in real-working conditions on the sea in misfiring and normal firing modes. Measurements focused on the AE signal acquired in a transverse direction in low-frequency (20–80 kHz), medium-frequency (100–400 kHz) and high-frequency (400–900 kHz) ranges. The collected signals were analyzed on the crank angle and crank angle-frequency domains. The results showed that all potential sources of the nonlinear AE signal could be mapped in the low-frequency range. However, only the AE signal caused by the combustion process at around the top dead center could be well-observed in the medium-to-high-frequency range. The findings also revealed that in normal firing conditions, the AE energy radiated by friction in the down-stroke period was smaller than in the up-stroke process due to gas-sealing forces. Moreover, the AE energy in the misfiring condition was higher than in the normal firing state. These outcomes considerably contributed understandings to characteristics of friction and wear around the mid-stroke area of the cylinder on a two-stroke marine diesel engine.

In this study, the optimization of air gap magnetic flux density of open slotted axial flux permanent magnet (AFPM) machine which was developed for wind turbine has been obtained using the Taguchi experimental method. For this, magnetic analyzes were performed by ANSYS Maxwell program according to Taguchi table. Then the optimum values have been determined and the average magnetic flux density values have been calculated for air gap and iron core under load and no-load conditions with ANSYS Maxwell. Traditionally, 15625 analyzes are required for 6 independent variables and 5 levels when experimental method is used. In this study, optimum values are determined by 25 magnetic analyzes, which use L25 orthogonal array. For this purpose, both factor effect graph and signal to noise ratios are used, according to the factors and levels which are obtained from the factor effect graph and the signal to noise ratio. Parameters are re-analyzed by Maxwell. The optimum factors and levels are determined. For optimized values, the air gap magnetic flux density is improved by 65.7% and 173.26%, respectively, according to the average value and the initial design. Therefore, the variables are optimized in a shorter time with Taguchi experimental design method instead of the traditional design method for open slotted AFPM generator. In addition, the results were analyzed statistically using ANOVA and Regression model. The variables were found to be significant by ANOVA. The degree of influence of the variables on the air gap magnetic flux density was also determined by the Regression model.