The aim of this paper is to present an assessment of the slip influence on the deflection of the steel plate-concrete composite beams, which are a new type of a design concept. The proposed method is based on the procedure included in the PN-EN 1992-1-1, which has been modified with taking into consideration interface slip. The theoretical analysis was verified by experimental studies.
Introduction of polymers into the cement composites improves same of the properties of concretes and mortars. Therefore, the polymer-cement composites are successfully used in construction. The model of microstructure formation in cement composites modified with thermoplastic polymer (pre-mix modifiers) has already been developed and successfully implemented. However, the formation of microstructure in the case of epoxy-cement composites (containing post-mix modifier) demonstrates same peculiarities which should be taken into account when modelling the process. The microstructure of epoxy-cement composites and its formation is discussed in the paper. The model is offered, formulated on the basis of the microscopic observations and results of testing.
In this stud y, we attempt to analyse free nonlinear vibrations of buckling in laminated composite beams. Two new methods are applied to obtain the analytical solution of the nonlinear governing equation of the problem. The effects of different parameters on the ratio of nonlinear to linear natural frequencies of the beams are studied. These methods give us an agreement with numerical results for the whole range of the oscillation amplitude.
The paper presents the response of a three-layered annular plate with damaged laminated facings to the loads acting in their planes. The presented problem concerns the analysis of the combination of global plate failure in the form of buckling with the local micro defects, like fibre or matrix cracks, located in the laminas. The plate structure consists of thin laminated, fibre-reinforced composite facings and a thicker foam core. The matrix and fibre cracks of facings laminas can be transversally symmetrically or asymmetrically located in plate structure. Critical static and dynamic stability analyses were carried out solving the problem numerically and analytically. The numerical results show the static and dynamic stability state of the composite plate with different combinations of damages. The final results are compared with those for undamaged structure of the plate and treated as quasi-isotropic ones. The analysed problem makes it possible to evaluate the use of the non-ideal composite plate structure in practical applications.
This paper presents an experimental analysis of flexural capacity and deformability of structural concrete slabs prepared as composite members consisting of two concrete layers made of reinforced ordinary concrete (N) and fiber reinforced concrete (SFRC). The reinforced concrete composite slabs used in the tests were prepared in the dimensions of 600 x 1200 x 80 mm. The basis was composed of two layers consisting of SFRC, one as the top layer, and one as ordinary concrete. The results of the analysis confirm a significant improvement of structural properties of the composite slab in comparison to the slabs prepared wholly of ordinary concrete.
This paper presents research results of composite tubes filled with self-compacting concrete. The impact of the selected materials and geometric factors on resistance to the vertical shear was evaluated in this study. The resistance of the tested members was compared with recommendations given in Eurocode PN-EN 1994-1-1. From the results obtained in the tests it can be deduced that more parameters should be taken into consideration when determining resistance to the vertical shear in the interface between steel and concrete than PN-EN 1994-1-1 recommends.
Definition of a composite [1] describes an ideal composite material with perfect structure. In real composite materials, structure is usually imperfect – composites contain various types of defects [2, 3–5], especially as the casted composites are of concern. The reason for this is a specific structure of castings, related to course of the manufacturing process. In case of metal matrix composite castings, especially regarding these manufactured by saturation, there is no classification of these defects [2, 4]. Classification of defects in castings of classic materials (cast iron, cast steel, non-ferrous alloys) is insufficient and requires completion of specific defects of mentioned materials. This problem (noted during manufacturing metal matrix composite castings with saturated reinforcement in Institute of Basic Technical Sciences of Maritime University Szczecin) has become a reason of starting work aimed at creating such classification. As a result, this paper was prepared. It can contribute to improvement of quality of studied materials and, as a consequence, improve the environment protection level.
The quest for airframe weight reduction results in a careful dimensioning cross section areas of structural airframe components depending on the anticipated loading. In the case of flanges of polymeric laminate spars subjected to tension such a dimensioning can be done by means of appropriate ply dropping along the spar flanges. A method for an effective calculation of the number of plies that can be cut off at the cross-section under consideration without excessive stress concentration resulted has been presented. The method takes advantage of the Linear Fracture Mechanics tools combined with simple finite element calculations. In addition, experimental data needed can be easily obtained with the use of inexpensive specimens that are simple for manufacturing and testing.
This paper presents the capabilities of ABAQUS finite-element program [1] in modelling sandwich beams and plates resting on deformable foundations. Specific systems of sandwich beams and plates separated by an elastic core layer were subjected to the action of point and distributed moving loads. A few theoretical examples are provided to present different techniques of modelling the foundations and the moving loads. The effects of the boundary conditions and of the foundation parameters on the deflections of the analysed structures are also presented.
This paper investigates the behaviour of axially-loaded tubular columns filled with M20 grade concrete and partially replaced concrete. The parameters varying in the study are slenderness ratio (13.27, 16.58 & 19.9), and normal M20 grade concrete, partially replaced quarry dust and concrete debris. The effects of the various concrete mixes and composite action between the steel tube and the concrete core are studied and a graph visualizing the differences between the load carrying capacity and the axial deflection is plotted. Some of the performance indices like the Ductility Index (DI), Concrete Contribution Ratio (CCR), Confinement Index (θ) and Strength Index (SI) are also evaluated and compared amongst the CFST columns. From the results it has been noted that an increase in the L/D ratio decrease the behaviour of the composite columns irrespective of the in filled materials. The composite action was achieved in the CFST columns filled with partially replaced quarry dust and concrete debris when compared with hollow steel columns. The load carrying capacity of the CFST column increases by 32 % compared with the hollow tubular columns.
Buckling and postbuckling response of thin-walled composite plates investigated experimentally and determinated analytically and numerically is compared. Real dimension specimens of composite plates weakened by cut-out subjected to uniform compression in laboratory buckling tests have been modelled in the finite element method and examined analytically based on P-w2 and P-w3 methods. All results were obtained during the experimental investigations and the numerical FEM analysis of a thin-walled composite plate made of a carbon-epoxy laminate with a symmetrical eight-layer arrangement of [90/-45/45/0]s. The instrument used for this purpose was a numerical ABAQUS® program.
The paper presents results of compressive strength investigations of EN AC-44200 based aluminum alloy composite materials reinforced
with aluminum oxide particles at ambient and at temperatures of 100, 200 and 250C. They were manufactured by squeeze casting of the
porous preforms made of α-Al2O3 particles with liquid aluminum alloy EN AC-44200. The composite materials were reinforced with
preforms characterized by the porosities of 90, 80, 70 and 60 vol. %, thus the alumina content in the composite materials was 10, 20, 30
and 40 vol.%. The results of the compressive strength of manufactured materials were presented and basing on the microscopic
observations the effect of the volume content of strengthening alumina particles on the cracking mechanisms during compression at
indicated temperatures were shown and discussed. The highest compressive strength of 470 MPa at ambient temperature showed
composite materials strengthened with 40 vol.% of α-Al2O3 particles.
Diagnostics of composite castings, due to their complex structure, requires that their characteristics are tested by an appropriate description
method. Any deviation from the specific characteristic will be regarded as a material defect. The detection of defects in composite castings
sometimes is not sufficient and the defects have to be identified. This study classifies defects found in the structures of saturated metallic
composite castings and indicates those stages of the process where such defects are likely to be formed. Not only does the author
determine the causes of structural defects, describe methods of their detection and identification, but also proposes a schematic procedure
to be followed during detection and identification of structural defects of castings made from saturated reinforcement metallic composites.
Alloys examination was conducted after technological process, while using destructive (macroscopic tests, light and scanning electron
microscopy) and non-destructive (ultrasonic and X-ray defectoscopy, tomography, gravimetric method) methods. Research presented in
this article are part of author’s work on castings quality.
The Copper-SiC composite was investigated with the help of FEM. The authors modeled and analyzed the effect of relaxation of thermal stresses due to seasoning at room temperature after the manufacturing process together with the effect of thermal stresses induced by reheating the material to a service temperature. Especially, hypothetical fracture at interface was of interest. It was shown that, for a fixed temperature, a single crack emanating at 0° or 45° azimuth would develop only along a portion of fiber perimeter, and a further growth would require stress increase in the fiber surrounding.
The paper describes the dynamics of a composite cantilever beam with an active element. The vibrations of the kinematically excited beam are controlled with the use of a Macro Fiber Composite actuator. A proportional control algorithm is considered. During the analysis, actuator is powered by a time-varying voltage signal that is changed proportionally to the beam deflection. The MFC element control system with the implemented algorithm allowed for changing the stiffness of the tested structure. This is confirmed by the numerical and experimental results. Resonance curves for the beam with and without control are determined. The results show a very good agreement in qualitative terms.
In this study, the vibration analysis of fully and partially treated laminated composite Magnetorheological (MR) fluid sandwich plates has been investigated experimentally. The natural frequencies of fully and partially treated laminated composite MR fluid sandwich plates have been measured at various magnetic field intensities under two different boundary conditions. The variations of natural frequencies with applied magnetic field, boundary conditions and location ofMRfluid pocket have been explored. Further, a comparison of natural frequencies of fully and partially treated MR fluid sandwich structure has been made at various magnetic field intensities.
Polymer composite materials based on the Moplen HP400R polypropylene matrix with a filler from walnut shell flour with 30, 40 and 50% content and 200-315 µm and 315-443 µm fraction were produced by the injection method. The effect of filler content was analysed on the processing properties of the composites such as: MFR Melt Flow Rate and the MVR Melt Volume-flow Rate, as well as the temperature of the filler flour decomposition using the TGA thermogravimetric analysis method. The following was also determined: density, hardness, tensile strength and stiffness modulus of elasticity of the materials in question. The obtained composite material was characterised by low density, which increased with the rising filler content. It was found that the applied natural filler has increased the hardness and stiffness modulus of the composite and decreased the tensile strength.
This study focuses to develop a new hybrid Engineered Cementitious Composite (ECC) and assesses the performance of a new hybrid ECC based on the steel short random fiber reinforcement. This hybrid ECC aims to improve the tensile strength of cementitious material and enhance better flexural performance in an RC beam. In this study, four different mixes have been investigated. ECC with Poly Vinyl Alcohol (PVA) fiber and PolyPropylene (PP) fiber of 2.0% volume fraction are the two Mono fiber mixes; ECC mix with PVA fiber of 0.65% volume fraction hybridized with steel fiber of 1.35% volume fraction, PP fiber of 0.65% volume fraction hybridized with steel of 1.35% volume fraction are the two additional different hybrid mixes. The material properties of mono fiber ECC with 2.0 % of PVA is kept as the reference mix in this study. The hybridization with fibers has a notable achievement on the uniaxial tensile strength, compressive strength, Young’s modulus, and flexural behavior in ECC layered RC beams. From the results, it has been observed that the mix with PVA fiber of 0.65% volume fraction hybrid with steel fiber of 1.35% volume fraction exhibitimprovements in tensile strength, flexural strength, andenergy absorption. ThePP fiber of 0.65% volume fraction hybridized with steel of 1.35% volume fraction mix has reasonable flexural performance and notable achievement in displacement ductility overthe reference mix.