Different methods are used for production of bronze bearings. In terms of technical specifications, the success of each of these methods
depends on the bond’s strength and in terms of economic, the production method is important. In this study, the aim is to study the strength
and microstructure of steel-bronze thrust bearing bond that has been produced through the casting using pre-mold. In this study, in order to
bond, the raw metals are chemically washed with sulfuric acid solution for five minutes at first. Then, the molten bronze SAE660 is cast in
a structural steel S235JR pre-mold. The bond’s strength has been measured using the shear test three times; the measurement of bond’s
length has been done using field emission scanning electron microscope (FESEM). The results indicate that the strength of the bond is at
least 94.8 MPa and bond’s length is 0.45 micrometers. Therefore, this method was successful for trust bearing application.
The paper presents the analysis of temperature fields, phase transformations, strains and stresses in a cuboidal element made from S235 steel, surfaced with multipass GMA (Gas Metal Arc) method. The temperature field is described assuming a dualdistribution heat source model and summing up the temperature fields induced by the padded weld and by the electric arc. Dependence of stresses on strains is assumed on the basis of tensile curves of particular structures, taking into account the influence of temperature. The calculations were carried out on the example of five welds in the middle of the plate made of S235 steel. The simulation results are illustrated in graphs of thermal cycles, volume shares of structural components and stresses at the selected points of cross-section, and the temperature and strain distributions in the whole cross section.
In calculating the resistance of welds within the connections between hollow sections in EN 1993‒1‒8, very general information is given without presenting specific calculations. The chief recommendations indicate that the resistance of the welds connecting the wall to the second element should not be less than the resistance of the cross section of the wall. In addition, assessment of the welds’ resistance based on the effective lengths is viable in cases when forces in the braces are smaller than the resistance of the joint, though the detailed method was not specified. The objective of this paper is to present the most up-to-date information about the design of overlap welded joints with a reinforcing rib plate.
The main goal of the article is to identify artificially created defects like lack of fusion and incomplete penetration in butt weld joint using non-destructive volumetric methods. These defects are the most serious defects in welds of steel constructions from the safety point of view. For identification, an ultrasonic phased array technique and a conventional X-ray using digital imaging were used. The theoretical part of the article describes the current state of the given issue and provides basic theoretical knowledge about ultrasonic and X-ray welding tests. In the experimental part, the procedure and results of testing butt weld joint are described by both non-destructive methods. The butt weld joint was made from steel S420MC. Each indication obtained by the ultrasonic and x-ray technique is supplemented by the macrostructure of the weld taken from the indication position. The results of the experimental work mentioned in the article point to the possibility and reliability of the identification of melting defects by selected nondestructive methods in terms of their character and orientation.
Friction stir welding is a solid state innovative joining technique, widely being used for joining aluminium alloys in aerospace, marine automotive and many other applications of commercial importance. The welding parameters and tool pin profile play a major role in deciding the weld quality. In this paper, an attempt has been made to understand the influences of welding speed and pin profile of the tool on friction stir welded joints of AA6082-T6 alloy. Three different tool pin profiles (tapered cylindrical four flutes, triangular and hexagonal) have been used to fabricate the joints at different welding speeds in the range of 30 to 74 mm/min. Microhardness (HV) and tensile tests performed at room temperature were used to evaluate the mechanical properties of the joints. In order to analyse the microstructural evolution of the material, the weld’s cross-sections were observed optically and SEM observations were made of the fracture surfaces. From this investigation it is found that the hexagonal tool pin profile produces mechanically sound and metallurgically defect free welds compared to other tool pin profiles.
This paper outlines issues associated with gas-shielded braze welding of CU-ETP copper with austenitic steel X5CrNi18-10 (1.4301) using a consumable electrode. The possibilities for producing joints of this type using innovative low-energy welding methods are discussed. The paper provides an overview of the results of metallographic and mechanical (static shear test, microhardness) tests for braze welded joints made on an automated station using the Cold Metal Transfer (CMT) method. Significant differences in the structure and mechanical properties are indicated, resulting from the joint configuration and the type of shielding gas (argon, helium).
Development of a reliable numerical model capturing major physical mechanisms controlling explosive welding and considering properties of all process components i.e. base plate and flyer plate is the goal of the paper. To properly replicate materials behavior under these severe conditions a meshfree approach, namely Smooth Particle Hydrodynamics (SPH), was used to discretize the computational domain. The model is based on the Mie-Gruneisen shock equation of state applied to the Ti/Cu system as a case study. Examples of results in the form of velocity, equivalent stress, equivalent strain, and pressure fields are presented within the paper.
The aim of that work was the evaluation of the quality of welded connections elements (welds) from the 30HGS steel and titanium alloy Ti6Al4V. The metallographic, factographic tests were used, and measurements of microhardness with the Vickers method. In the head weld of the 30HGS steel there were non-metallic partial division and bubbles observed. The average microhardness in the head connection was 320 HV0.1. There was no significant increase/decrease observed of microhardness in the head influence zone of the weld. There was a good condition of head connections observed, in accordance with the standard EN12517 and EN25817. In the head weld of Ti6Al4V titanium alloy there were single, occasional non-metallic interjections and bubbles observed. There were no cracks both on the weld, and on the border of the heat influence zone. The value of microhardness in head connection was in the range 300÷445 HV0.1. Reveal a very good condition of the head connections in accordance with the standard EN12517 and EN25817. The factographic tests prove the correctness of welded connections done and then heat treatment in case of steel and titanium alloy.
The article provides results of the microstructure examinations and mechanical properties (hardness and microhardness tests) of the welded joint T91 steel taken from the live steam pipeline. Examined joint has been exploited for about 45 000 hours in a temperature of 535oC and the steam pressure equals to 13.5 MPa. Examined joint was made as a double bead by the additional materials with a different chemical composition. It was proved that the joint was characterized by a differential microstructure on the cross-section of the weld. Moreover, decarburized zone in the lower alloyed material and carbides zone in the higher alloyed material were revealed in the weld line and on the boundary penetration of beads. Furthermore, it was shown that the main mechanism of a joint degradation is a privileged precipitation of carbides on the grain boundaries, and an increase of their size.
The article discusses tests concerning the assessment of the corrosion resistance, properties and the structure of TIG braze welded galvanised steel sheets. Test butt joints were made of 0.9 mm thick galvanised car body steel sheets DC04 (in accordance with EN 10130), using a robotic welding station and a CuSi3Mn1 braze (in accordance with PN-EN 13347:2003) wire having a diameter of 1.0 mm. The research-related tests aimed to optimise braze welding parameters and the width of the brazing gap. The test joints were subjected to visual tests, macro and microscopic metallographic tests, hardness measurements as well as tensile and bend tests. The corrosion resistance of the joints was identified using the galvanostatic method. The tests revealed that it is possible to obtain high quality joints made of galvanised car body steel sheets using the TIG braze welding process, the CuSi3Mn1 braze and a brazing gap, the width of which should be restricted within the range of 0.4 mm to 0.7 mm. In addition, the joints made using the aforesaid parameters are characterised by high mechanical properties. The minimum recommended heat input during process, indispensable for the obtainment of the appropriate spreadability of the weld deposit should be restricted within the range of 50 kJ/mm to 70 kJ/mm. At the same time, the aforesaid heat input ensures the minimum evaporation of zinc. Joints made using the TIG braze welding method are characterised by high resistance to electrochemical corrosion. The galvanostatic tests did not reveal any traces of corrosion in the joint area.