Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 6
items per page: 25 50 75
Sort by:
Download PDF Download RIS Download Bibtex

Abstract

The paper presents a new kind of vibrator, called the intelligent vibrator, which is an integrated set of two inert vibrators supplied by asynchronous squirrel-cage motors, equipped with digital control system, the readout system of the position of unbalanced masses, and inverter supply system. The paper presents a model of the prototype of the machine and exemplary run-times.
Go to article

Authors and Affiliations

Mariusz Giergiel
Download PDF Download RIS Download Bibtex

Abstract

The paper discusses an occurrence or latent reactions in the direction perpendicular to the movement of the suspension systems in vibratory machines supported by parallel leaf springs. These reactions occur despite an apparent lack of any forces acting in that direction and may - for long machine bodies - reach values comparable with the exciting force of the vibrator. Analytical relationships allowing for estimation of the value of reactions were derived. The obtained results were verified by means of the Geometric Element Method as well as by the performed experiments.
Go to article

Authors and Affiliations

Jerzy Michalczyk
Piotr Czubak
Download PDF Download RIS Download Bibtex

Abstract

The article presents an example of finishing treatment for aluminum alloys with the use of vibration machining, with loose abrasive media in a closed tumbler. For the analysis of selected properties of the surface layer prepared flat samples of aluminum alloy PA6/2017 in the state after recrystallization. The samples in the first stage were subjected to a treatment of deburring using ceramic media. In a second step polishing process performed with a strengthening metal media. In addition, for comparative purposes was considered. only the case of metal polishing. The prepared samples were subjected to hardness tests and a tangential tensile test. As a result of finishing with vibratory machining, it was possible to remove burrs, flash, rounding sharp edges, smoothing and lightening the surface of objects made. The basic parameters of the surface geometry were obtained using the Talysurf CCI Lite - Taylor Hobson optical profiler. As a result of the tests it can be stated that the greatest reduction of surface roughness and mass loss occurs in the first minutes of the process. Mechanical tests have shown that the most advantageous high values of tensile strength and hardness are obtained with two-stage vibration treatment, - combination of deburring and polishing. Moreover the use of metal media resulted in the strengthening of the surface by pressure deburring with metal media.

Go to article

Authors and Affiliations

D. Bańkowski
S. Spadło
Download PDF Download RIS Download Bibtex

Abstract

The article presents the results of research on the finishing of M63 Z4 brass by vibratory machining. Brass alloy was used for the research due to the common use of ammunition elements, cartridge case and good cold forming properties on the construction. Until now, the authors have not met with the results of research to determine the impact of abrasive pastes in container processing. It was found that the additive for container abrasive treatment of abrasive paste causes larger mass losses and faster surface smoothing effects. The treatment was carried out in two stages: in the first stage, the workpieces were deburred and then polished. Considerations were given to the impact of mass of workpieces, machining time and its type on mass loss and changes in the geometric structure of the surface. The surface roughness of machining samples was measured with the Talysurf CCI Lite optical profiler. The suggestions for future research may be to carry out tests using abrasive pastes with a larger granulation of abrasive grains, and to carry out tests for longer processing times and to determine the time after which the parameters of SGP change is unnoticeable.

Go to article

Authors and Affiliations

D. Bańkowski
ORCID: ORCID
S. Spadło
Download PDF Download RIS Download Bibtex

Abstract

This article proposes these of vibratory machining to Ti-6Al-4V titanium alloy as finishing treatment. Titanium alloy was used in the aerospace industry, military, metallurgical, automotive and medical processes, extreme sports and other. The three-level three-factor Box-Behnken experiment examined the influence of machining time of vibratory machining, the type of mass finishing media used and the initial state of the surface layer on the mass loss, geometric structure of the surface, micro hardness and the optimal process parameters were determined. Considerations were given the surfaces after milling, after cutting with a band saw and after the sanding process. The experiment used three types of mass finishing media: polyester, porcelain and metal. Duration of vibratory machining treatment was assumed to be 20, 40, 60 minutes. The form profiles before and after vibratory machining were determined with the Talysurf CCI Lite - Taylor Hobson optical profiler. Future tests should concern research to carry out tests using abrasive pastes with a larger granulation of abrasive grains, to carry out tests for longer processing times and to determine the time after which the parameters of geometrical structure of the surface change is unnoticeable.

Go to article

Authors and Affiliations

D. Bańkowski
ORCID: ORCID
S. Spadło
Download PDF Download RIS Download Bibtex

Abstract

The paper presents an example of the application of vibratory machining for castings based on the results of visual testing. The purpose of the work is to popularize non-destructive testing and vibratory machining as finishing process, especially in the case of cast objects. Visual testing is one of the obligatory non-destructive tests used for castings and welded joints. The basic requirements concerning the dimensional accuracy and surface texture of cast components are not met if visible surface flaws are detected. The tested castings, which had characteristic traces of the casting process, were subjected to vibratory machining. The machining with loose abrasive media in vibrating containers is aimed at smoothing the surface and reducing or completely removing flashes. To complement the visual testing were also conducted research on the contact profilometer Taylor Hobson PGI 1200. Particular attention was focused on measuring the height of flashes and changes in the surface of smoothed details based on BNIF No. 359 touch-visual patterns. Based on the work, it can be concluded that vibratory machining allows for removal flashes and smoothing of the surface of aluminum alloy cast objects.

Go to article

Authors and Affiliations

D. Bańkowski
ORCID: ORCID
P. Młynarczyk
ORCID: ORCID

This page uses 'cookies'. Learn more