The contributions of work-hardening of austenite and the presence of martensite on the hardening of an AISI 304L stainless steel were evaluated based on plastic deformation under different reductions in thickness at two rolling temperatures. The cold deformation temperatures of 300 K and 373 K were chosen to induce strain-hardening plus strain-induced martensitic transformation in the former and strain-hardening in the latter. This made it possible to elucidate the real effects of strengthening mechanisms of metastable austenitic stainless steels during mechanical working.

The article presents a precise method for the orientation process of NiMnGa-based single crystals. For this method, a scanning electron microscope equipped with an EBSD camera and a heating stage allowing temperatures exceeding 873 K was used. The orientation process was carried out in both the high-temperature austenite phase and in the room-temperature martensite phase. The facilities allowed for determining the orientation of a single grain of austenite at elevated temperatures as well as the orientation of particular martensitic variants at room temperature. A practically perfect cubic orientation was obtained in the austenitic case with a deviation of about 1° while the samples oriented in the martensitic phase deviated from the desired orientation by 4.5-5.2°. Additionally, the training process of single crystals was carried out in order to show the influence of the orientation process on twinning stress.

The most commonly quenching process for carburizing gears is the oil-quenching (OQ) and salt-quenching (SQ), and finite analysis and comparison of OQ and SQ on the carburizing gear ring were performed. Wherein, the accurate simulation of gear carburization was obtained by the alloying element coefficient for diffusion coefficient and experiment validation. The heat transfer coefficients measured by the inverse heat transfer method was used to the temperature simulation, and the gear distortion mechanism was analyzed by the simulated results. By the comparison of OQ, SQ had higher cooling capacity in the high temperature region and slow cooling rate in the temperature range where martensite transformation occurs. The martensite transformation was more sufficient, and the compressive stress of the tooth was greater in the SQ. The tooth showed a drum-shaped and slight saddle-shaped distortion in the OQ and SQ, respectively. The simulated distortion results have good consistency with the measured results, and the SQ distortion was more uniform and stable based on the measured results.

In this paper, the influence of Mo addition on the structure and mechanical properties of the NiCoMnIn alloys have been studied. Series of polycrystalline NiCoMnIn alloys containing from 0 to 5 mas.% of Mo were produced by the arc melting technique. For the alloys containing Mo, two-phase microstructure was observed. Mo-rich precipitates were distributed randomly in the matrix. The relative volume fraction of the precipitates depends on the Mo content. The numbers of the Mo rich precipitates increases with the Mo contents. The structures of the phases were determined by the TEM. The mechanical properties of the alloys are strongly affected by Mo addition contents. Brittleness of the alloys increases with the Mo contents.

Grey cast iron belongs to materials for casting production, which have wide application for different industry branches. Wide spectrum of

properties of these materials is given by the structure of base metal matrix, which can be influenced with heat treatment. Processes of

annealing can be applied for grey cast iron without problems. During heat treatment processes, where higher cooling rates are used, the

thermal and structural strains become important. Usage and conditions of such heat treatment for grey cast iron castings of common

production are the subject of evaluation of this article.

The austenitic stability and strain-induced martensitic transformation behavior of a nanocrystalline FeNiCrMoC alloy were investigated. The alloy was fabricated by high-energy ball milling and spark plasma sintering. The phase fraction and grain size were measured using X-ray diffraction. The grain sizes of the milled powder and the sintered alloy were confirmed to be on the order of several nanometers. The variation in the austenite fraction according to compressive deformation was measured, and the austenite stability and strain-induced martensitic transformation behavior were calculated. The hardness was measured to evaluate the mechanical properties according to compression deformation, which confirmed that the hardness increased to 64.03 HRC when compressed up to 30%.

We propose an empirical equation to predict the martensite start temperatures of highly alloyed steels containing more than 3 wt.% of Ni or Cr or 2 wt.% of Mo, W, or Co. The martensite start temperature calculated by the proposed equation was in good agreement with experimental data owing to not only the derivation from experimental data of alloy steels with a wide range of chemical compositions but also the interaction term between carbon and carbide-forming alloying elements.

For the EN GX4CrNi13-4 martensitic stainless steel, research was conducted to investigate the impact of the quenching intensity and the content of nickel on the mechanical properties and amount of retained austenite. It was found that the amount of retained austenite significantly increases with growing nickel concentration. On the other hand, the cooling rate at quenching makes a difference only if the cooling is intensive, then amount of retained austenite decrease. A higher nickel content improves the mechanical properties. With more intensive cooling, the tensile strength decreases while the yield strength increases. The ductility is not significantly affected by the cooling intensity.

The paper presents the results of the Ti10V2Fe3Al alloy crack resistance assessment using the Rice’s J-integral technique as a function of morphology and volume fraction of α-phase precipitates. Titanium alloys characterized by the two-phase structure α + β are an interesting alternative to classic steels with high mechanical properties. Despite the high manufacturing costs and processing of titanium alloys, they are used in heavily loaded constructions in the aerospace industry due to its high strength to density ratio. The literature lacks detailed data on the influence of microstructure and, in particular, the morphology of α phase precipitates on fracture toughness in high strength titanium alloys. In the following work an attempt was made to determine the correlation between the microstructure and resistance to cracking in the Ti10V2Fe3Al alloy.

In this study, microstructural and crystallographic properties of phase transformations occurring with thermal effect in Fe-XMn-Mo-Si (X = 15.14wt.% ve 18.45wt.%) alloys have been investigated. The effects of (wt.%) Mn rates in the alloy on the characteristics of phase transformations were investigated by using Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD). SEM and TEM investigations was observed that two different martensite (ε and α') structures were formed in austenite grain. In addition, in TEM observations, the interface regions were selected over the bright field image. Crystallographic orientation relationships were obtained by the analyses of electron diffraction patterns from the interface regions. γ → α' type transformation was observed for α' particle formation, and orientation relationship was found as (1–11)γ // (011)α', [101]γ // [1–11–]α' and, γ → ε type transformation was observed for ε martensite plate formation, and the orientation relationship was found as (1–11–)γ // (0002–)ε, [1–1–0]γ // [2–110]ε. It was noticed that this orientation relationships were compatible with the literature (Kurdjumov-Sachs and Shoji-Nishiyama orientation relationship). Precipitation phase (carbide) formation was observed in microstructure analyses. The changes in the magnetic properties of the alloys having different rates of Mn as a consequence of thermal effect phase transformations was investigated by using Mössbauer Spectroscopy. The internal magnetic field, volume fractions (transformation rates), isomer shift values and magnetic characteristics of the main and product phases were revealed by Mössbauer Spectroscopy. In the Mössbauer Spectrum, it was noticed that ε-martensite and γ-austenite structures showed paramagnetic single-peak, and α'-martensite showed ferromagnetic six-peaks.

As one of the most promising 3rd generation advanced high strength steels (AHSS), medium Mn steels attract much attention because of their exceptional mechanical property and reasonable cost. However, their application in the modern automotive industry is limited by poor weldability. In this study, 7Mn steel was welded by resistance spot welding (RSW), which was followed by high-temperature annealing to increase the cross-tension property. With this effort, enhanced cross-tension strength (CTS) with a partial interfacial fracture (PIF) mode was realized. During the annealing after RSW that produced martensite, austenitization was realized and then evolved into martensite by the following air cooling. This process produced structure homogeneity across the joint. With respect to the RSW joint, martensite remained the dominant structure after annealing while the diffusion of C and Mn solutes was triggered. With the increase of annealing temperature, the diffusion was enhanced, and the grain boundary embrittlement was reduced, leading to higher CTS.

We investigated the austenite stability and mechanical properties in FeMnNiC alloy fabricated by spark plasma sintering. The addition of Mn, Ni, and C, which are known austenite stabilizing elements, increases its stability to a stable phase existing above 910°C in pure iron; as a result, austenitic microstructure can be observed at room temperature, depending on the amounts of Mn, Ni, and C added. Depending on austenite stability and the volume fraction of austenite at a given temperature, strain-induced martensite transformation during plastic deformation may occur. Both stability and the volume fraction of austenite can be controlled by several factors, including chemical composition, grain size, dislocation density, and so on. The present study investigated the effect of carbon addition on austenite stability in FeMnNi alloys containing different Mn and Ni contents. Microstructural features and mechanical properties were analyzed with regard to austenite stability.

Co-Cr-Mo based sheet I-WP lattice was fabricated via laser powder bed fusion. The effect of microstructure and the I-WP shape on compressive mechanical response was investigated. Results of compression test showed that yield strength of the sheet I-WP was 176.3 MPa and that of bulk Co-Cr-Mo (reference material) was 810.4 MPa. By applying Gibson-Ashby analytical model, the yield strength of the lattice was reversely estimated from that of the bulk specimen. The calculated strength of the lattice obtained was 150.7 MPa. The shape of deformed lattice showed collective failure mode, and its microstructure showed that strain-induced martensitic transformation occurred in the overall lattice. The deformation behavior of additively manufactured sheet I-WP lattice was also discussed.