The multi-phase permanent-magnet machines with a fractional-slot concentrated-winding (FSCW) are a suitable choice for certain purposes like aircraft, marine, and electric vehicles, because of the fault tolerance and high power density capability. The paper aims to design, optimize and prototype a five-phase fractional-slot concentrated-winding surface-mounted permanent-magnet motor. To optimize the designed multi-phase motor a multi-objective optimization technique based on the genetic algorithm method is applied. The machine design objectives are to maximize torque density of the motor and maximize efficiency then to determine the best choice of the designed machine parameters. Then, the two-dimensional Finite Element Method (2D-FEM) is employed to verify the performance of the optimized machine. Finally, the optimized machine is prototyped. The paper found that the results of the prototyped machine validate the results of theatrical analyses of the machine and accurate consideration of the parameters improved the acting of the machine.
FEM (finite element method) is an essential and powerful numerical method that can explicitly optimize the design process of electrical devices. In this paper, the employment of FEM tools such as SolidWorks, COMSOL and ANSYS is proposed in order to aid electrical apparatuses engineering and modeling – those are arc chambers of modular circuit breakers. Procured models of arc chambers have been undergoing simulations concerning heating, electric potential distribution, electric charge velocity and traverse paths. The data acquired has been juxta-positioned against experimental data procured in the Short-Circuit Laboratory, Warsaw University of Technology. The reflection of the theoretical approach was clearly noted in the experimental results. Mutual areas of the modeled element expressed the same physical properties and robustness errors when tested under specific conditions – faithfully reflecting those which were experimented with. Moreover, the physical phenomena essential for electrical engineering could be determined already at the model stage. This procedure proved highly valuable during designing/engineering work in terms of material economy.
A single acoustic vector sensor (AVS) cannot be used to find the direction-of-arrival (DOA) of two or more coherent (fully correlated) sources. We have proposed a technique for estimating DOAs (in 2D geometry) of two simultaneous coherent sources using single AVS under the assumption that acoustic sources enter in the field sequentially. The DOA estimation has been investigated with two different configurations of AVS, each consisting of three microphones in a plane. The technique has been also applied in tracking (a) an acoustic source in the presence of stationary interfering coherent source and (b) two coherent sources when the sources are changing their locations alternatively. The experimental environment has been generated using the Finite-Element Method tool viz. COMSOL to corroborate the proposed scheme.
The paper presents the results of experimental-numerical tests of firing at aluminum composite materials. The test materials were manufactured by pressure infiltration of porous ceramic preforms made of -Al2O3 particles in the amount of 30% and 40% by volume. The EN AW-7075 alloy was chosen as the material matrix, and the steel 7.62×39 mm (M 43) FMJ (Full Metal Jacket) intermediate ammunition was selected for firing. In the result of the experiment, the samples were perforated with a clear difference in the muzzle diameter. The projectile with fragments caused damage to up to three reference plates placed behind the samples (witness plates) in composites with 40% of particles by volume. The mechanics of crack propagation during ballistic impacts of the projectile was characterized based on microstructure studies. Then, using numerical analysis of impact load, the examination of composite materials puncture in the ABAQUS environment was carried out. The Finite Element Method (FEM) was employed for the discretization of geometric models using Hex elements. The Johnson-Cook constitutive model describing the relationship between stress and strain in metal-ceramic composites was applied for the analyses. Numerical models were then subjected to numerical verification using smoothed particle hydrodynamics (SPH). Based on the obtained results, it was found that the hybrid FEM/SPH method correlates significantly with the experimental results.
This paper presents the results of Finite Element Method (FEM) modeling of double-twisted steel hexagonal wire mesh used to construct gabion cages. Gabion cages, filled with soil (usually rock particles) are commonly used in civil engineering (for example in order to form a retaining wall). Static tensile tests are modeled and the obtained force - displacements curves are compared with the laboratory test results (known from literature). Good accordance between numerical and laboratory test results is observed. Three different material models for single wire and double twist are tested. Special attention is paid to double-twist modelling. Simulations of the damaged mesh are also performed, strength and stiffness reduction is analyzed. Anisotropic membrane model for mesh is proposed and calibrated. Parameters for homogenized Coulomb - Mohr media for gabion (filling and mesh) are estimated. Such homogenized Coulomb - Mohr model could be used in engineering practice to model behaviour of real gabion structures.