Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 6
items per page: 25 50 75
Sort by:
Download PDF Download RIS Download Bibtex

Abstract

Catalytic properties of activated carbons oxidized, treated with N-compounds, and promoted with copper were studied in selective catalytic reduction NOX by ammonia (NH3-SCR). The modification of the catalysts consisted of a series of steps (pre-oxidation of activated carbon, impregnation with urea, impregnation with copper). The physicochemical properties of the obtained samples were determined using X-ray diffraction, FT-IR spectroscopy, and low-temperature N2 sorption. The modification with copper improved the catalytic activity and stability of the catalysts. All the functionalized carbon doped with copper reached more than 90% of NO conversion and CO2 did not exceed 240 ppm at 220 ◦C. The sample doped with 5 wt.% Cu had the maximum NO conversion of 98% at 300 ◦C. The maximum N2O concentration detected for the same sample was only 55 ppm, which confirmed its selectivity.

Go to article

Authors and Affiliations

Marwa Saad
Anna Białas
Przemysław Grzywacz
Cezary Czosnek
Bogdan Samojeden
Monika Motak
Download PDF Download RIS Download Bibtex

Abstract

In the last few years, cationic layered clays, including bentonites have been investigated as potential catalysts for SCR DeNOx systems. In this work, bentonite as the representative of layered clays was modified in order to obtain an alternative, low-cost NH3–SCR catalyst. Samples of raw clay were activated with HCl or HNO3, treated with C2H2O4 and subsequently pillared with alumina by the ion- exchange. Afterwards, the modified materials were impregnated with iron and copper. The obtained catalysts were characterized by XRD and FT-IR. SCR catalytic tests carried out over analyzed samples indicated the conversion of NO of approximately 90% for the most active sample. The type of acid used for modification and the type of active phase strongly influenced the catalytic properties of the analyzed materials.

Go to article

Authors and Affiliations

Agmieszka Szymaszek
Maciej Kubeł
Bogdan Samojeden
Monika Motak
Keywords de-NOx ozone mixing
Download PDF Download RIS Download Bibtex

Abstract

The influence of ozone injection mode on the effectiveness of nitrogen monoxide oxidation to nitrogen dioxide by ozone in a flow reactor was investigated experimentally in laboratory apparatus. Nitrogen monoxide was diluted to the mole fraction 100 ppm in air which served as the carrier gas flowing through the tube of the diameter D = 60 mm into which ozone was injected. The effects of a number of ozone injecting nozzles and their configuration on the effectiveness of NO oxidation were examined. In the closest vicinity from the injection site the counter-current injection mode appeared to be superior to the co-current injection mode, but in areas located further from the injection site both injection systems were almost equally effective.

Go to article

Authors and Affiliations

Maciej Jakubiak
Włodzimierz Kordylewski
Download PDF Download RIS Download Bibtex

Abstract

The results of experimental investigations on the removal of NOx from gases applying ozone as the oxidizing agent and the absorption of higher nitrogen oxides in the sodium hydroxide solutions are presented. The experiment was conducted using a pilot plant installation with the air flow rate 200 m3/h, being a prototype of a boiler flue gas duct and a FGD scrubber. It was shown that in the range of [NOref] = 50 ÷ 250 ppm the mechanism of NO ozonation depends on the molar ratio X = O3/NOref: for X ≤ 1.0 oxidation of NO to NO2 predominates and NO2 is poorly absorbed, for X >> 1.0 NO2 undergoes further oxidation to N2O5, which is efficiently absorbed in the scrubber. The stoichiometric molar ratio of complete conversion of NO into N2O5 is X = 1.5, in these studies to reach the effectiveness η ≥ 90% the molar ratio X was much higher (2.75).

Go to article

Authors and Affiliations

Włodzimierz Kordylewski
Maciej Jakubiak
Tomasz Hardy
Download PDF Download RIS Download Bibtex

Abstract

The paper presents results of experimental studies on removal of NOx from flue gas via NO ozonation and wet scrubbing of products of NO oxidation in NaOH solutions. The experiment was conducted in a pilot plant installation supplied with flue gas from a coal-fired boiler at the flow rate 200 m3/h. The initial mole fraction of NOx,ref in flue gas was approx. 220 ppm, the molar ratio X = O3/NOref varied between 0 and 2.5. Ozone (O3 content 1÷5% in oxygen) was injected into the flue gas channel before the wet scrubber. The effect of the mole ratio X, the NaOH concentration in the absorbent, the liquid-to-gas ratio (L/G) and the initial NOx concentration on the efficiency of NOx removal was examined. Two domains of the molar ratio X were distinguished in which denitrification was governed by different mechanisms: for X ≤ 1.0 oxidation of NO to NO2 predominates with slow absorption of NO2, for X >> 1.0 NO2 undergoes further oxidation to higher oxides being efficiently absorbed in the scrubber. At the stoichiometric conditions (X = 1) the effectiveness of NO oxidation was better than 90%. However, the effectiveness of NOx removal reached only 25%. When ozonation was intensified (X ≥ 2.25) about 95% of NOx was removed from flue gas. The concentration of sodium hydroxide in the aqueous solution and the liquid-to-gas ratio in the absorber had little effect on the effectiveness of NOx removal for X > 2.

Go to article

Authors and Affiliations

Maciej P. Jakubiak
Włodzimierz K. Kordylewski
Download PDF Download RIS Download Bibtex

Abstract

A process capable of NOx control by ozone injection gained wide attention as a possible alternative to proven post combustion technologies such as selective catalytic (and non-catalytic) reduction. The purpose of the work was to develop a numerical model of NO oxidation with O3 that would be capable of providing guidelines for process optimisation during different design stages. A Computational Fluid Dynamics code was used to simulate turbulent reacting flow. In order to reduce computation expense a 11-step global NO - O3 reaction mechanism was implemented into the code. Model performance was verified by the experiment in a tubular flow reactor for two injection nozzle configurations and for two O3/NO ratios of molar fluxe. The objective of this work was to estimate the applicability of a simplified homogeneous reaction mechanism in reactive turbulent flow simulation. Quantitative conformity was not completely satisfying for all examined cases, but the final effect of NO oxidation was predicted correctly at the reactor outlet.

Go to article

Authors and Affiliations

Norbert J. Modliński
Włodzimierz K. Kordylewski
Maciej P. Jakubiak

This page uses 'cookies'. Learn more