The paper deals with the problem of force and torque calculation for linear, cylindrical and spherical electromechanical converter.
The electromagnetic field is determined analytically with the help of separation method for each problem. The results obtained can be used as test tasks for electromagnetic field, force and torque numerical calculations. The analytical relations for torque and forces are also convenient for analysis of material parameters influence on electromechanical converter work.
While analyzing shape accuracy of ferroalloy precision castings in terms of ceramic moulds physical anisotropy, low-alloy steel castings
("cover") and cast iron ("plate") were included. The basic parameters in addition to the product linear shape accuracy are flatness
deviations, especially due to the expanded flat surface which is cast plate. For mentioned castings surface micro-geometry analysis was
also carried, favoring surface load capacity tp50 for Rmax = 50%.
Surface load capacity tp50 obtained for the cast cover was compared with machined product, and casting plate surface was compared with
wear part of the conveyor belt. The results were referred to anisotropy of ceramic moulds physical properties, which was evaluated by
studying ceramic moulds samples in computer tomography equipment Metrotom 800.
The study attempts to investigate the influence of severe plastic deformation (SPD in the hydrostatic extrusion (HE) process on the anisotropy of the structure and mechanical properties of the AA 6060 alloy. Material in isotropic condition was subjected to a single round of hydrostatic extrusion with three different degrees of deformation (ε = 1.23, 1.57, 2.28). They allowed the grain size to be fragmented to the nanocrystalline level. Mechanical properties of the AA 6060 alloy, examined on mini-samples, showed an increase in ultimate tensile strength (UTS) and yield strength (YS) as compared to the initial material. Significant strengthening of the material results from high grain refinement in transverse section, from »220 μm in the initial material to »300 nm following the HE process. The material was characterized by the occurrence of structure anisotropy, which may determine the potential use of the material. Static tensile tests of mini-samples showed »10% anisotropy of properties between longitudinal and transverse cross-sections. In the AA6060 alloy, impact anisotropy was found depending on the direction of its testing. Higher impact toughness was observed in the cross-section parallel to the HE direction. The results obtained allow to analyze the characteristic structure created during the HE process and result in more efficient use of the AA 6060 alloy in applications.
Anisotropy of variations of Polish mineral deposit parameters is rarely the subject of interest of geologists who carry on the assessment projects . However, if the anisotropy is strong its description and mathematical modeling are rational and justified as it may affect the accuracy of many calculations suitably for mining geology and mining engineering, e.g. estimation of resources and grade of particular raw-material, interpolation of deposit parameters values and construction of their contour maps, designing of optimum grade mining operations or densification of sampling grid. In geostatistics anisotropy is described with directional semivariograms which represent average variability of values of particular deposit parameter in various directions, depending on the distance between sampling sites. Convenient graphic presentation of anisotropy is map of directional semivariograms and good mathematical presentation are functions describing the anisotropy models.
The paper presents the results of geostatistical descriptions of various anisotropy types in selected examples of Polish mineral deposits. Taking into account the spherical variability model, the influence of anisotropy on the results of deposit parameters estimations has been theorized for both the interpolation point and calculation block (area). It was found that anisotropy is effective for parameters estimation if three mutually interrelated factors are considered: power of directional diversification of parameters variation, contribution of random component to total, observed variation of parameters and the range of semivariograms (autocorrelation) of parameter referred to the average sampling grid density.
The results demonstrate that anisotropy influences much more the estimations of parameters value in interpolation points than those of average values of parameters calculated for particular parts of deposit (calculation blocks). Moreover, anisotropy is unimportant when the random component of variability dominates the overall variability of analyzed parameter. Therefore, the simpler, isotropic variability model can be applied to geostatistical estimations of deposit parameters.
For the purpose of making of a solid body of an electric guitar the acoustic- and mechanical properties of walnut- (Juglans regia L.) and ash wood (Fraxinus excelsior L.) were researched. The acoustic properties were determined in a flexural vibration response of laboratory conditioned wood elements of 430 × 186 × 42.8 mm used for making of a solid body of an electric guitar. The velocity of shearand compression ultrasonic waves was additionally determined in parallel small oriented samples of 80 × 40 × 40 mm. The research confirmed better mechanical properties of ash wood, that is, the larger modulus of elasticity and shear modules in all anatomical directions and planes. The acoustic quality of ash wood was better only in the basic vibration mode. Walnut was, on the other hand, lighter and more homogenous and had lower acoustic- and mechanical anisotropy. Additionally, reduced damping of walnut at higher vibration modes is assumed to have a positive impact on the vibration response of future modelled and built solid bodies of electric guitars. When choosing walnut wood, better energy transfer is expected at a similar string playing frequency and a structure resonance of the electric guitar.
Magnetic properties of silicon iron electrical steel are determined by using standardized measurement setups and distinct excitation parameters. Characteristic values for magnetic loss and magnetization are used to select the most appropriate material for its application. This approach is not sufficient, because of the complex material behavior inside electrical machines, which can result in possible discrepancies between estimated and actual machine behavior. The materials’ anisotropy can be one of the problems why simulation and measurement are not in good accordance.With the help of a rotational single sheet tester, the magnetic material can be tested under application relevant field distribution. Thereby, additional effects of hysteresis and anisotropy can be characterized for detailed modelling and simulation.
The Goss texture is a characteristic feature of grain-oriented transformer steel sheets. Generator sheets, which are produced as non-oriented steel sheets, should have isotropic features. However, measurement results of generator sheets, confirmed by crystallographic studies, indicate that these sheets are characterized by certain, quite significant anisotropy. The first purpose of this paper is to present the influence of textures of generator and transformer steel sheets on their magnetization characteristics. The second aim is to propose a method which takes into account the sheet textures in the calculations of magnetization curves. In calculations of magnetization processes in electrical steel sheets, models in which the plane of a sheet sample is divided into an assumed number of specified directions are used. To each direction a certain hysteresis loop, the so-called direction hysteresis, is assigned. The parameters of these direction hystereses depend, among other things, on the texture type in these steel sheets. This paper discusses the method which calculates the parameters of these direction hystereses taking into account the given sheet texture. The proposed method gives a possibility of determining the magnetization characteristics for any direction of the field intensity changes.
An axially symmetric, gravity driven, steady flow of a grounded polar ice sheet with a prescribed temperature field is considered.
The ice is treated as an incompressible, non-linearly viscous, anisotropic fluid, the internal structure (fabric) of which evolves as ice descends from the free surface to depth in an ice sheet. The evolution of the ice fabric is described by an orthotropic constitutive law which relates the deviatoric stress to the strain-rate, strain, and three structure tensors based on the current (rotating) principal stretch axes. The solution of the problem is constructed as a leading-order approximation derived from asymptotic expansions in a small parameter that reflects the small ratio of stress and velocity gradients in the lateral direction of the ice sheet to those in the thickness direction. Numerical simulations of the flow problem have been carried out for various sets of rheological parameters defining the limit strength of the anisotropic fabric in ice. The results of calculations illustrate the influence of the ice anisotropy, basal melt conditions and temperature field in ice on the glacier thickness and lateral span, and on the depth profiles of the flow velocity.
A multi-laminate constitutive model for soft soils incorporating structural anisotropy is presented. Stress induced anisotropy of strength, which is present in multi-laminate type constitutive models, is augmented by directionally distributed overconsolidation. The model is presented in theelastic-plastic version in order to simulate strength anisotropy of soft clayey soils and destructuration effects. Performance of the model is shown for some element tests and for the numericalsimulation of a trial road embankment constructed on soft clays at Haarajoki, Finland. The numerical calculations are completed with the commercial finite element code capable to performcoupled static/consolidation analysis of soils. Problems related to the initiation of in situ stress state, conditions of preconsolidation, as well as difficulties linked to estimation of the model parametersare discussed. Despite simple assumptions concerning field conditions and non-viscous formulationof the constitutive model, the obtained final results are of a sufficient accuracy for geotechnical practice.
We have presented dielectric and conductivity studies of two liquid crystal (LC) compounds- p-octyloxybenzoic acid (8OBA) and p-decyloxybenzoic acid (10OBA). Dielectric permittivity study of those compounds gives the evidence of space charge polarization and ionic conductance in the samples. Dielectric permittivity is found to be the highest for 8OBA than 10OBA. Both compounds found to exhibit positive dielectric anisotropy. Splay elastic constant as a function of temperature has also been investigated. Frequency and temperature dependent electrical conductivity of these two LC compounds have been studied in detail. Activation energy has been estimated from both dc and ac conduction process.
The behaviour of energy levels and optical spectra of a charged particle (electron or hole) confined within a potential well of ellipsoidal shape is investigated as a function of the shape-anisotropy parameter. If two energy levels of the same symmetry intersect in a perturbation-theory approximation, they move apart on direct diagonalization of the appropriate Hamiltonian. The intersection of the energy levels leads to a discontinuity of the corresponding dipole-moment matrix element. The discontinuity of matrix elements is not reflected in the behaviour of transition probabilities which are continuous functions of the shape-anisotropy parameter. The profiles of a spectral line emitted or absorbed by an ensemble of ellipsoidally shaped nanoparticles with a Gaussian distribution of size are calculated and discussed.
In the present investigation optical, electro-optical and dielectric properties have been measured for nematic liquid crystal (NLC) material 1550C which consists of 4’-(trans, trans-4-alkylbicyclohexyl) carbonates and 4’-(4-(trans,trans-4-alkyl)-4-cyanobicyclohexane, dispersed with fluorescent dye (Benzo 2,1,3 Thiadiazole) in two different concentrations. Photoluminescence has been enhanced for a dye dispersed system which is the key finding of this investigation. UV absorbance study has also been performed and found to be increased for composite system. Enhanced birefringence after dispersion of dye into pure NLC is also a prominent result of this investigation. Relative permittivity, threshold voltage and dielectric anisotropy have also been measured and found to be increased. The outcome of the present work may be very useful in the construction of liquid crystal displays (LCDs).
Mechanical properties of the pipeline samples that had been cut in annular and axial directions were investigated. The methodology of modeling and calculation of the real stress-strain state was described. The stable state during in the deformation process was defined. The results of the experimental researches were used as a test variant during examination of pipe strength.
Bełchatów lignite deposit is located in the central partof Poland in the tectonic Kleszczów graben. It is dividedinto several parts, which are mining fields: Kamieńsk area (eastern part of the deposit), Bełchatów area (central partof the deposit) and Szczerców area (western part of the deposit). The subject of this study was the Belchatow area.The main issue of the investigations was the dependence of local, regional and global, horizontal variability of selected lignite qualitative parameters (moisture, ash content, calorific value and sulfur content in the as receivedstate) is a function of viewing direction. There was applied the geostatistical analysis of the lignite variability parameters with use of semivariograms.
The researches which were conducted at different scales of observation: in the locale scale – in small field size8 ́8 m called experimental area (local analysis), in larger homogeneous separated parts of the Belchatow area(regional analysis) and in the whole Bełchatów area scale (general analysis). The results proved the visible anisotropy of variability mine lignite parametres. Anisotropy structure observed in regional and global scale isconnected with tectonic structure of the Bełchatów Graben. The detailed studies show the variated level of anisotropy observed in different areas of Bełchatów field.
However, no dependence of the relative level of ash and total sulfur content anisotropy on the environment of sedimentation of the main coal deposit in different parts of the Belhchatów field has been observed. Both parameters characterize with strong or medium anisotropy level in examined fields. Moreover, anisotropy is alsovisible in the local scale. Conducted researches confirmed the thesis that zonal anisotropy is prevalent kind of anisotropy in the regional scale. In the range of the whole deposit the total sulfur content showed zonal anisotropy,whereas the ash content revealed geometric anisotropy
The main purpose of the paper is to present a method which allows taking into account the anisotropic properties of dynamo steel sheets. An additional aim is to briefly present anisotropic properties of these sheets which are caused by occurrences of some textures. In order to take into account textures occurring in dynamo sheets, a certain sheet sample is divided into elementary segments. Two matrix equations, describing changes of the magnetic field, are transformed to one non-linear algebraic equation in which the field strength components are unknown. In this transformation the flux densities assigned to individual elementary segments are replaced by functions of flux densities of easy magnetization axes of all textures occurring in the given dynamo sheet. The procedure presented in the paper allows determining one non-linear matrix equation of the magnetic field distribution; in this equation all textures occurring in a dynamo sheet are included. Information about textures occurring in typical dynamo sheets may be used in various approaches regarding the inclusion of anisotropic properties of these sheets, but above all, the presented method can be helpful in calculations of the magnetic field distribution in anisotropic dynamo sheets.
The aim of the paper is to formulate physically well founded yield condition for initially anisotropic solids revealing the asymmetry of elastic range. The initial anisotropy occurs in material primarily due to thermo-mechanical pre-processing and plastic deformation during the manufacturing processes. Therefore, materials in the “as-received” state become usually anisotropic. After short account of the known limit criteria for anisotropic solids and discussion of mathematical preliminaries the energy-based criterion for orthotropic materials was formulated and confronted with experimental data and numerical predictions of other theories. Finally, possible simplifications are discussed and certain model of isotropic material with yield condition accounting for a correction of shear strength due to initial anisotropy is presented. The experimental verification is provided and the comparison with existing approach based on the transformed-tensor method is discussed.