The road network development programme, as well as planning and design of transport systems of cities and agglomerations require complex analyses and traffic forecasts. It particularly applies to higher-class roads (motorways and expressways), which in urban areas, support different types of traffic. Usually there is a conflict between the needs of long-distance traffic, in the interest of which higher-class roads run through undeveloped areas, and the needs of bringing such road closer to potential destinations, cities [1]. By recognising the importance of this problem it is necessary to develop the research and methodology of traffic analysis, especially trip models. The current experience shows that agglomeration models are usually simplified in comparison to large city models, what results from misunderstanding of the significance of these movements for the entire model functioning, or the lack of input data. The article presents the INMOP 3 research project results, within the framework of which it was attempted to increase the accuracy of traffic generation in agglomeration model owing to the use of BigData – the mobile operator’s data on SIM card movements in the Warsaw agglomeration.
The spectroscopic FT-IR and FT-Raman methods allowed to identify the cross-linking process of the aqueous composition of poly(acrylic
acid)/sodium salt of carboxymethyl starch (PAA/CMS-Na) applied as a binder for moulding sands (as a novel group binders BioCo). The
cross-linking was performed by physical agent, applying the UV-radiation. The results of structural studies (IR, Raman) confirm the
overlapping of the process of cross-linking polymer composition PAA/CMS-Na in UV radiation. Taking into account the ingredients and
structure of the polymeric composition can also refer to a curing process in a binder - mineral matrix mixture. In the system of bindermineral
matrix under the influence of ultraviolet radiation is also observed effect of binding. However, the bonding process does not occur
in the entire volume of the investigated system, but only on the surface, which gives some possibilities for application in the use of UV
curing surface of cores, and also to cure sand moulds in 3D printing technology
Within the INMOP 3 research project, an attempt was made to solve a number of problems associated with the methodology of modelling travel in urban areas and the application of intermodal models. One of these is the ability to describe the behaviour of transport system users, when it comes to making decisions regarding the selection of means of transport and searching for relationships between travel describing factors and the decisions made in regard of means of transport choice.
The paper describes a probabilistic approach to the determination of modal split, and the application of a logistic regression model to determine the impact of variables describing individual and mass transport travels on the probability of selecting specific means of transport. Travels in local model of Warsaw city divided into 9 motivation groups were tested, for which ultimately 8 models were developed, out of which 7 were deemed very well fitted (obtained pseudoR2 was well above 0.2).
In order to increase wear resistance cast steel casting the TiC-Fe-Cr type composite zones were fabricated. These zones were obtained by
means of in situ synthesis of substrates of the reaction TiC with a moderator of a chemical composition of white cast iron with nickel of
the Ni-Hard type 4. The synthesis was carried out directly in the mould cavity. The moderator was applied to control the reactive
infiltration occurring during the TiC synthesis. The microstructure of composite zones was investigated by electron scanning microscopy,
using the backscattered electron mode. The structure of composite zones was verified by the X-ray diffraction method. The hardness of
composite zones, cast steel base alloy and the reference samples such as white chromium cast iron with 14 % Cr and 20 % Cr, manganese
cast steel 18 % Mn was measured by Vickers test. The wear resistance of the composite zone and the reference samples examined by ballon-disc
wear test. Dimensionally stable composite zones were obtained containing submicron sizes TiC particles uniformly distributed in
the matrix. The macro and microstructure of the composite zone ensured three times hardness increase in comparison to the cast steel base
alloy and one and a half times increase in comparison to the white chromium cast iron 20 % Cr. Finally ball-on-disc wear rate of the
composite zone was five times lower than chromium white cast iron containing 20 % Cr.
Refinement is one of the most energy consuming technological process, aimed at obtaining mineral raw materials of the proper grain size.
Cast structural elements such as jaws or hammers in crushing machines operate under conditions of an intensive wear. The data indicate
that 80 % of failures of machines and devices is caused by wearing of rubbing surfaces. This problem became the subject of several
scientific and industrial investigations carried out in the whole world in order to produce materials ultra- wear resistant. Methods allowing
to obtain wear resistant composite castings are discussed in the hereby paper. Within the performed research microstructures of the
produced composite zones were presented and the comparative analysis with regard to mechanical and functional properties of local
composite reinforcements in relation to the commercial alloys of increased wear resistance was performed. The results show almost twenty
five times increase in wear resistance compared to manganese cast steel containing 18 % Mn.
Traffic related noise is currently considered as an environmental pollution. Paper presents results of multidirectional study attempting to serve urban traffic without the need to erect noise barriers interfering urban space. Initial concept of the road expansion included construction of 1000 m of noise barriers dividing city space. Improvement in the acoustic conditions after construction completion is possible due to the applied noise protection measures: vehicle speed limit, smooth of traffic flow, use of road pavement of reduced noise emission and the technical improvement of the tramway.