In this paper, flow systems which are commonly used in fittings elements such as contractions in ice slurry pipelines, are experimentally investigated. In the study reported in this paper, the consideration was given to the specific features of the ice slurry flow in which the flow behaviour depends mainly on the volume fraction of solid particles. The results of the experimental studies on the flow resistance, presented herein, enabled to determine the loss coefficient during the ice slurry flow through the sudden pipe contraction. The mass fraction of solid particles in the slurry ranged from 5 to 30%. The experimental studies were conducted on a few variants of the most common contractions of copper pipes: 28/22 mm, 28/18 mm, 28/15 mm, 22/18 mm, 22/15 mm and 18/15 mm. The recommended (with respect to minimal flow resistance) range of the Reynolds number (Re about 3000-4000) for the ice slurry flow through sudden contractions was presented in this paper.

According to The European Commission’s regulation numbers 842/2006 and 517/2014, refrigerants whose Global Warming Potential ratio is more than 150, have been prohibited in mobile air conditioning (MAC) since January 2017. Therefore, the commonly used R-134 gas has been banned. The search for a new refrigerant, which grants all the required criteria, has begun. In accordance with new European standards, the gas should have environmentally friendly properties and should not be noxious to human life while operating. In this paper, two alternative substances, which can substitute the banned R134a, have been compared. This is synthetic R1234yf, which belongs to the HFO group, and carbon dioxide, which exists in the natural environment. The chemical build, physical and thermodynamic properties have been described. Scientific articles, which present and compare the technical results of testing both refrigerants, have been discussed. Comparison results, tools used and research methodology have been described in these articles. Alternative gases have been analyzed for their environmental impact and have been checked on the toxic, flammable, impact on ozone depletion and global warming. The threats to human life due to the use of the new refrigerants have been reviewed. The thesis also comprises an economical comparison between the two gases. A short review and conclusions have been presented at the end of the article.

The paper stresses the issue of strong temperature influence on the gain of a Silicon Photomultiplier (SiPM). High sensitivity of the detector to light (single photons) requires stable parameters during measurement, including gain. The paper presents a method of compensating the change of gain caused by temperature variations, by adjusting a suitable voltage bias provided by a precise power module. The methodology of the research takes in account applications with a large number of SiPMs (20 thousand), explains the challenges and presents the results of the gain stabilization algorithm.

The primary aim of this paper was to assess the development of prosumer energy sector in Poland. In the first point, the basic notions connected with prosumer energy (micro-installation, prosumer) were discussed on the basis of Law of Renewable Energy Sources of February 20, 2015 (Journal of Laws, item 478, as amended) and the main aspects of the European Union energy policy where presented in the context of the development of the prosumer energy sector. In this part of the study, numerous benefits for the Polish economy and consumers of electrical energy, connected with the expansion of prosumer energy sector, were presented. On the other hand, many obstacles which stall this sector in Poland were noticed. In the second point the most important regulations from the Law of Renewable Energy Sources of February 20, 2015 were analyzed (In the second point the most important regulations from the Law of Renewable Energy Sources of February 20, 2015 (hereinafter: the RES act) were analyzed). On the basis of this legal act, the so called “rebate system”, which is currently used in Poland to support prosumers of electrical energy, was described. Moreover, many legal and administrative simplifications implemented by the RES act were indicated. The analytical approach to the RES Act in this study resulted in the detection of many regulations in this legal act which may have an adverse impact on the development of the prosumer energy sector in Poland. In the third point, programs co-financed by the Polish government or the European Union, which financially support the purchase and installation of energy technologies using RES, were described. Statistical data connected with the prosumer energy sector in Poland was presented in the fourth point of this paper. On the basis thereof, the authors attempted to find the correlation between the number of prosumers and the share of the amount of electrical energy from renewable energy sources in gross electrical energy consumption. In the fifth point issues connected with energy technologies used in the Polish prosumer energy sector were discussed. Moreover, this point focuses on the great popularity of photovoltaic modules among Polish prosumers and results in the reluctance of Polish prosumers to install wind microturbines and small hydroelectric power plants.

The purpose of this article was to discuss the use of adsorption chillers for waste heat recovery. The introduction discusses the need to undertake broader measures for the effective management of waste heat in the industry and discusses the benefits and technical problems related to heat recovery in industrial plants. In addition, heat sources for adsorption chillers and their application examples were described. The principle of operation of adsorption chillers is explained in the next chapter. Heat sources for adsorption chillers are indicated and their application examples are described. The above considerations have allowed the benefits and technical obstacles related to the use of adsorption chillers to be highlighted. The currently used adsorbents and adsorbates are discussed later in the article. The main part of the paper discusses the use of adsorption chillers for waste heat management in the glassworks. The calculations assumed the natural gas demand of 20.1 million m3 per year and the electricity demand of 20,000 MWh/year. As a result of conducted calculations, a 231 kW adsorption chiller, ensuring the annual cold production of 2,021 MWh, was selected. The economic analysis of the proposed solution has shown that the investment in the adsorption chiller supplied with waste heat from the heat recovery system will bring significant economic benefits after 10 years from its implementation, even with total investment costs of PLN 1,900,000. However, it was noted that in order to obtain satisfactory economic results the production must meet the demand while the cost of building a heat recovery system shall not exceed PLN 1 million.

Adsorption cooling and desalination technologies have recently received more attention. Adsorption chillers, using eco-friendly refrigerants, provide promising abilities for low-grade waste heat recovery and utilization, especially renewable and waste heat of the near ambient temperature. However, due to the low coefficient of performance (COP) and cooling capacity (CC) of the chillers, they have not been widely commercialized. Although operating in combined heating and cooling (HC) systems, adsorption chillers allow more efficient conversion and management of low-grade sources of thermal energy, their operation is still not sufficiently recognized, and the improvement of their performance is still a challenging task. The paper introduces an artificial intelligence (AI) approach for the optimization study of a two-bed adsorption chiller operating in an existing combined HC system, driven by low-temperature heat from cogeneration. Artificial neural networks are employed to develop a model that allows estimating the behavior of the chiller. Two crucial energy efficiency and performance indicators of the adsorption chiller, i.e., CC and the COP, are examined during the study for different operating sceneries and a wide range of operating conditions. Thus this work provides useful guidance for the operating conditions of the adsorption chiller integrated into the HC system. For the considered range of input parameters, the highest CC and COP are equal to 12.7 and 0.65 kW, respectively. The developed model, based on the neurocomputing approach, constitutes an easy-to-use and powerful optimization tool for the adsorption chiller operating in the complex HC system.