The present study, aims to investigate the effect of minor Zr and Nb alloying on soft magnetic and electrical properties of Fe86(ZrxNb1-x)7B6Cu1 (x = 1, 0.75, 0.5, 0.25) alloys. The investigated alloys were prepared through the melt spinning process. Within the examined compositional range (Nb up to 5.25at%, respectively), the soft magnetic properties and electrical resistivity of the alloys continuously increase with increasing Nb content. However increasing the Nb content further decreases such properties. We could confirm the influence of ratio of Zr and Nb on grain growth and crystallization fraction during crystallization by using the soft magnetic properties and electrical properties.

This study investigated the effect of T6 heat treatment on the microstructure and scratch wear behavior of hypoeutectic ­Al-12wt.%Si alloy manufactured by extrusion. Microstructural observation identified spherical eutectic Si phases before and after the heat treatment of alloys (F, T6). Phase analysis confirmed Al matrix and Si phase as well as Al2Cu and Al3Ni, Mg2Si in both alloys. In particular, Al2Cu was finer and more evenly distributed in T6 alloy. This resulted in Vickers hardness of T6 alloy that was 2.3 times greater compared to F alloy. The scratch wear test was conducted using constant load scratch test (CLST) mode and multi-pass scratch test (MPST) mode. The scratch coefficient and worn out volume obtained by such were used to evaluate wear properties before and after heat treatment. In the case of T6 alloy, its scratch coefficient was lower than F alloy in all load ranges. After 15 repeated tests to measure worn out volume, F alloy and T6 alloy measured 1.2×10–1 mm3 and 7.8×10–2 mm3, respectively. In other words, the wear resistance of T6 alloy were confirmed to be better than those of F alloy. In addition, this study attempted to identify the microstructural factors that contribute to the better scratch wear resistance of T6 alloy and wear mechanism from surface and cross-section observations after the wear tests.

Al and Nb-doped Li7La3Zr2O12 (LLZO) and W-doped LLZO lithium ion conducting electrolyte samples were prepared and their H2O stability was investigated. The LLZO samples were exposed to 50% humidified air for 48 h. After H2O exposure, a cubic to tetragonal transformation occurred and acquired SEM images exhibited the presence of reaction phases at the grain boundaries of Al and Nb-LLZO. As a result, the lithium ion conductivity significantly decreased after H2O exposure. On the contrary, W-LLZO showed good stability against H2O. Although the cubic to tetragonal transformation was also observed in H2O-exposed W-LLZO, the decrease in lithium ion conductivity was found to be modest. No morphological changes of the W-LLZO samples were confirmed in the H2O-exposed W-LLZO samples.

In this study, agar-based nanocomposite films containing ultra-porous silica aerogel particles were fabricated by gel casting using an aqueous agar/silica aerogel slurry. The silica aerogel particles did not show significant agglomeration and were homogeneously distributed in the agar matrix. Transmission electron microscopy observations demonstrated that the silica aerogel particles had a mesoporous microstructure and their pores were not incorporated into the agar polymer molecules. The thermal conductivities of the agar and agar/5 wt.% silica aerogel nanocomposite films were 0.36 and 0.20 W·m–1·K–1, respectively. The transmittance of the agar films did not decrease upon the addition of silica aerogel particles into them. This can be attributed to the anti-reflection effect of silica aerogel particles.

Effects of various friction stir processing (FSP) variables on the microstructural evolution and microhardness of the AZ31 magnesium alloy were investigated. The processing variables include rotational and travelling speed of the tool, kind of second phase (i.e., diamond, Al2O3, and ZrO2) and groove depth (i.e., volume fraction of second phase). Grain size, distribution of second phase particle, grain texture, and microhardness were analyzed as a function of the FSP process variables. The FSPed AZ31 composites fabricated with a high heat input condition showed the better dispersion of particle without macro defect. For all composite specimens, the grain size decreased and the microhardness increased regardless of the grooved depth compared with that of the FSPed AZ31 without strengthening particle, respectively. For the AZ31/diamond composite having a grain size of about 1 μm, microhardness (i.e., about 108 Hv) was about two times higher than that of the matrix alloy (i.e., about 52 Hv). The effect of second phase particle on retardation of grain growth and resulting hardness increase was discussed.