In this work, the effect of heat transfer during explosive welding (EXW) and post-processing annealing on the microstructural and chemical composition changes have been thoroughly analysed using scanning and transmission electron microscopies and X-ray synchrotron radiation. Several combination of explosively welded metal compositions were studied: Ti with Al, Cu with Al, Ta or stainless steel, stainless steel with Zr or Ta and Ti with carbon steel. It was found that the melted metals exhibit a strong tendency to form brittle crystalline, nano-grained or even amorphous phases during the solidification. For all analysed metal combinations most of the phases formed in the zones of solidified melt do not appear in the equilibrium phase diagrams. Concurrently, the interfacial layers undergo severe plastic deformation forming nano-grained structures. It has been established that these heavily deformed areas can undergo dynamic recovery and recrystallization already during clad processing. This leads to the formation of new stress-free grains near the interface. In the case of low temperature and short time post processing annealing only the melted zones and severely deformed layers undergo recovery and recrystallization. However, drastic changes in the microstructure occurs at higher temperature and for longer annealing times. Applying such conditions leads to diffusion dominant processes across the interface. As a consequence continuous layers of intermetallic phases of equilibrium composition are obtained.

In this work, vacuum hot pressed Ni-Mn-Sn-In Heusler alloys with different concentration of In (0, 2 and 4 at.%), were investigated. The magneto-structural behaviour and microstructure dependencies on chemical composition and on heat treatment were examined. It was found that the martensite start transformation temperature increases with growing In content and to a lesser extent with increasing temperature of heat treatment. The high energy X-ray synchrotron radiation results, demonstrated that both chemical composition as well as temperature of heat treatment slightly modified the crystal structures of the studied alloys. Microstructural investigation performed by transmission electron microscopy confirmed chemical composition and crystal structure changes in the alloys.

In this paper, the microstructural and texture changes in polycrystalline CuZn30 alloy, copper, and AA1050 aluminium alloy have been studied to describe the crystal lattice rotation during shear bands formation. The hat-shaped specimens were deformed using a drop-hammer at the strain rate of 560 s ^–1. Microstructure evolution was investigated using optical microscopy, whereas texture changes were examined with the use of a scanning electron microscope equipped with the EBSD facility. The microstructural observations were correlated with nanohardness measurements to evaluate the mechanical properties of the sheared regions. The analyses demonstrate the gradual nature of the shear banding process, which can be described as a mechanism of the bands nucleation and then successive growth rather than as an abrupt instability. It was found that regardless of the initial orientation of the grains inside the sheared region, a well-defined tendency of the crystal lattice rotation is observed. This rotation mechanism leads to the formation of specific texture components of the sheared region, different from the one observed in a weakly or non-deformed matrix. During the process of rotation, one of the {111} planes in each grain of the sheared region ‘tends’ to overlap with the plane of maximum shear stresses and one of the <110> or <112> directions align with the shear direction. This allows slip propagation through the boundaries between adjacent grains without apparent change in the shear direction. Finally, in order to trace the rotation path, transforming the matrix texture components into shear band, rotation axis and angles were identified.

The new cast steel with a chemical composition of Fe-(0.85-0.95)C-(1.50-1.60)Si-(2.40-2.60)Mn-(1.0-1.2)Al-(0.30-0.40)­Mo-(0.10-0.15)V-(1.0-1.1)Ni (all in wt.%) was investigated in aspect of formation of the multiphase microstructure leading to high strength and ductility. Two types of heat treatment technologies were developed. The first one involves softening annealing at a temperature of 650°C for 4 hours, heating up to 950°C and holding for 2 hours, and then fast cooling down to 200°C and isothermally treated for 2 hours. The second one involves homogenizing annealing at 1100°C for 6 hours, then cooling with furnace down to 950°C and holding for 2 hours, then fast cooling down to 200°C and isothermally treated for 2 hours. A unique microstructure of cast steel consisting of martensite and retained austenite plates of various thicknesses and volume fractions was obtained. Additionally, nanometric transition carbides were noticed after the above-mentioned heat treatments. This microstructure ensures high hardness, strength and plasticity ( Rm = 1426 MPa and A = 9.5%), respectively, due to the fact that TWIP/TRIP processes occur during deformation related to the high volume fraction of retained austenite, which the stacking fault energy is above 15 mJ/m ^–2 resulting from the chemical composition of the investigated cast steel.

The article presents a precise method for the orientation process of NiMnGa-based single crystals. For this method, a scanning electron microscope equipped with an EBSD camera and a heating stage allowing temperatures exceeding 873 K was used. The orientation process was carried out in both the high-temperature austenite phase and in the room-temperature martensite phase. The facilities allowed for determining the orientation of a single grain of austenite at elevated temperatures as well as the orientation of particular martensitic variants at room temperature. A practically perfect cubic orientation was obtained in the austenitic case with a deviation of about 1° while the samples oriented in the martensitic phase deviated from the desired orientation by 4.5-5.2°. Additionally, the training process of single crystals was carried out in order to show the influence of the orientation process on twinning stress.

Two single crystals with compositions Fe-Ni-Co-Al-Ta and Fe-Ni-Co-Al-Ta-B were selected and fabricated by Bridgman method. Subsequently, ingots were homogenized, oriented and subjected to a two-step heat treatment process in order to obtain fine and coherent γ' precipitates. Subsequently, superelastic cycling experiments were performed at 77 K. The next step included detailed microstructural characterization using transmission electron microscopy and high-energy synchrotron X-ray diffraction measurements together with Rietveld refinement. The results show that the number of fully reversible superelastic strains is very sensitive to the size of γ' precipitates. The smaller (3 nm) γ' precipitates ensured more superelastic response compared to material with larger γ' particles size (5 nm), in which the material did not receive its original shape after 10 cycles even after being heated.

This study aimed to develop Fe/Al multilayered metallic/intermetallic composites produced by hot pressing under an air atmosphere. Analyses were carried out on the composite plates made up of alternatively situated sheets of AA1050 aluminum alloy and DN04 low carbon steel, which were annealed at 903 K for 2, 5, and 10 h. Annealing was performed to obtain reaction layers of distinct thickness. The samples were examined using X-Ray diffraction and scanning and transmission electron microscope equipped with an energy-dispersive X-Ray spectrometer. To correlate the structural changes with mechanical properties, microhardness measurements in near-the-interface layers were performed. All the reaction layers grew with parabolic kinetics with η-Al5Fe2 intermetallic phase as the dominant component. After annealing for 5 and 10 hours, a thin sublayer of θ-Al13Fe4 phase was also detected.

In the present work, we performed the ultra-rapid annealing (URA) process for amorphous Fe78Ni8B14 melt-spun ribbons in order to obtain fine excellent microstructure assuring the best soft magnetic properties. Several microscopic methods mainly based on transmission electron microscopy (TEM) and Lorentz TEM (L-TEM) were applied for detailed studies of the microstructure and magnetic domains structure. The investigation revealed that the optimized parameters of the URA process (500°C/0.5-5 s) lead to outstanding soft magnetic properties. A mixture containing close to 50% amorphous phase and 50% α-Fe nanocrystals of size up to 30 nm has been already obtained after annealing for 3 s. These annealing conditions appear to be the most suitable in terms of microstructure providing the best magnetic properties.