The five-layer Aurivillius type structures with the general chemical formula Bi5Fe2-xMnxTi3O18, where x = 0, 0.6, 1.2 have been synthesized and tested. The SEM studies showed a significant increase in grain size in the manganese-modified Aurivillius type ceramic material (for x = 1.2). The increase in the amount of manganese ions (Mn3+) affects the decrease in the temperature at which the relaxation processes take place. Namely from 525 K (1 kHz) and 725 K (1 MHz) for BFT sample (x = 0) to 355 K (1 kHz) and 565 K (1 MHz) for BFM12T sample (x = 1.2). Using the Arrhenius’s law and the Vogel-Fulcher’s relationship the activation energy (Ea) and the relaxation time have been calculated. The value of Ea increases with the increase of the Mn amount from 0.737 eV (for x = 0) to 0.915 eV (for x = 1.2).

Multiferroic composites are very promising materials because of their applicability because the magnetoelectric effect occurs in them. The subject of the study were two multiferroic ceramic composites: leaded obtained from powder of the composition PbFe0.5Nb0.5O3 and ferrite powder of the composition Ni0.64Zn0.36Fe2O4 and unleaded which was obtained from the powder of the composition BaFe0.5Nb0.5O3 and the same ferrite powder Ni0.64Zn0.36Fe2O4. For the both multiferroic materials the following studies were conducted: SEM, BSE, EDS, XRD and the temperature dependence of dielectric constant ε(T). Using the previously developed method of calculating the magnetoelectric coupling factor (g), based on dielectric measurements, the magnitude of the magnetoelectric effect in the multiferroic composites was determined.

The paper presents the study results of laser modification of Vanadis-6 steel after diffusion boronized. The influence of laser beam fluence on selected properties was investigated. Diffusion boronizing lead to formation the FeB and Fe2B iron borides. After laser modification the layers were consisted of: remelted zone, heat affected zone and substrate. It was found that increase of laser beam fluence have influence on increase in dimensions of laser tracks. In the thicker remelting zone, the primary dendrites and boron eutectics were detected. In the thinner remelting zone the primary carbo-borides and eutectics were observed. In obtained layers the FeB, Fe2B, Fe3B0.7C0.3 and Cr2B phases were detected. Laser remelting process caused obtained the mild microhardness gradient from the surface to the substrate. In the remelted zone was in the range from 1800 HV0.1 to 1000 HV0.1. It was found that the laser beam fluence equal to 12.7 J/mm2 was most favorable. Using this value, microhardness was relatively high and homogeneous.

The aggregate of various taxonomic groups of microorganisms colonising living organisms is known as the microbiome. The plant microbiome encompasses a wide network of biological, chemical and metabolic interactions between the plant and microorganisms (mainly algae, bacteria and protozoa). The relationships between microbes and peatland plants, particularly carnivorous plants, are a very interesting subject that is still little understood. Microbes colonising carnivorous peatland plants may be present in their traps or on the surface of the plant. Previous research on the relationships between the microbiome composition of carnivorous plants and the external factors influencing it directly and indirectly is still inadequate. There is a lack of review articles analysing the current state of knowledge regarding carnivorous plant–microbiome interactions. This review of the literature is a collection of data on the functioning of the microbiome of carnivorous plants growing in peatland ecosystems. In addition, it summarises the available information on host–microorganism relationships.

The waste production is closely related with human activity. Various approaches have been applied to manage and reduce its increasing volume (Paranjpe et al. 2023). One of the possibilities that comply with the assumptions of circular economy is utilization of wastes in anaerobic digestion (AD) process. This technology is common worldwide and it is recognized as the cost-effective methods of energy generation that also allow for nutrient recovery, as well as effective waste management (Alharbi et al. 2023). The biogas generated within this process is considered as a multifunctional renewable source that might be a promising alternative to the depleting traditional fuels. It finds various applications such as heat and power generation, fuel in automobiles, and substrate in chemical industry (Shitophyta et al. 2022, Pradeshwaran 2024). Typically, biogas contains 50–70% of CH4, 30–50% of CO2, and 1–10% of other trace gases like H2, H2S, CO, N2. Its composition mainly depends on the feedstock characteristics, operational conditions, and adopted technology (Gani et al. 2023, Archana et al. 2024). Considering further application, the priority action should be increasing its volume and methane content. There are several strategies to achieve these goals, including implementing codigestion strategy, adding additional component to the main substrate, introducing trace elements essential in AD, pretreatment strategies, and introducing enzymes and microbial strains to digesters (Zhang et al. 2019). Each method has limits related to the implementation costs, changes in the adopted technology, operator training needs, and additional energy input, which might negatively influence the energy balance of wastewater treatment plants (WWTPs) (Meng et al. 2022). Therefore, recent scientific attention has focused on combining various strategies to achieve intended goals. Moreover, such combinations might allow for an effective utilization of various wastes, the earlier use of which in AD was difficult. Orange waste could be an example of such a substrate. The previous studies indicated that its application in AD resulted in poor process efficiency, mainly due to the presence of limonene, recognized as the main inhibitor of biological activity (Calabro et al. 2020, Bouaita et al. 2022). In this study, the novel concept of implementing solidified carbon dioxide (SCO2) in the anaerobic co-digestion of municipal sewage sludge (SS) and orange peel waste (OPW) has been proposed. This approach may help overcome the disadvantages of the two-component AD of these wastes. Importantly, such studies have not been conducted thus far. However, the recent studies indicated that application of SCO2 to aerobic granular sludge improved biogas and methane yields and also enhanced the kinetics of biogas production (Kazimierowicz et al. 2023 a,b). Importantly, SCO2 might be generated in biogas upgrading technologies (Yousef 2019). Such solution is consistent with the principles of the circular economy and contributes to reducing the carbon footprint of WWTPs.

Multiferroic six-layer Aurivillius type Bi7Fe3Ti3O21 ceramics was obtained by conventional mixed oxides method. The final sintering process was taken in several different sintering times, which determined changes in properties of discussed ceramic material. The structure and dielectric properties of the material are reported. In order to examine the technological conditions on the crystal structure, XRD analysis was carried out. The microstructure, as well as the quantitative and qualitative analysis of the chemical composition were investigated by scanning electron microscope with an energy dispersion spectrometer. The main purpose of the paper is to present the effect of sintering time on the microstructure, crystallographic structure and dielectric properties of Bi7Fe3Ti3O21 ceramics.