On the basis of 35 one-hour series of the measurement of the wind velocity, read out every two minutes, the wind structure at the Arctowski Station, situated on Admiralty Bay, King George Island, was analysed. Very strong turbulence was found with air flow directions from over the area of the Island (S, SW. W and NW) and laminarity with directions from SE, E, NE and partly N, i.e. when the air flows from Admiralty Bay or from over the open waters of Bransfield Strait. The qustiness coefficient, the relationship between the maximum and mean velocities and the intensity of turbulence were determined for the two flow types. Two extremely different cases, in terms of flow character, were considered, by determining for them the distributions of instantaneous velocities and those of oscillations.
Power spectrum techniques were applied to two time series of wind speed values recorded at the Arctowski Station in order to investigate the influence of turbulent and laminar air flow on the quasi-periodicity of the micro-scale wind structure.
The analysis of speed and direction distribution of upper wind in the layer up to 3500 m was carried out on the basis of pibal ascents performed over the Admiralty Bay (King George Island, South Shetland Islands).
The research paper presents the results of the dynamic analysis of an existing bar dome subjected to wind loads. The calculation model of the structure was constructed using the finite element method. The dome was subjected to the standard wind pressure, assuming that it is operates in a harmonic manner. The numerical analyses were performed with the application of Autodesk Robot and MES3D. The analysis focused on the impact of selected factors such as the frequency of forcing, wind gustiness coefficient and structural damping on the behaviour of structures.
Wind constitutes one of the major environmental factors affecting the design and performance of built environment. Each country has its unique climatic wind conditions, and the way in which these are considered and implemented in the structural design, is important. An implementation or adoption of any new engineering design stipulations introduces a formidable challenge to the developers of the standards and the design profession. This has been experienced in some of the countries (e.g. the UK, Australia and the USA), where processes of modernising the outdated codifi cation took place in the past. Although both Poland and South Africa are currently at the early implementation stage of the new wind loading design stipulations, there is a major difference between the circumstances of the two countries. Poland, as an EU member state, has a compulsory obligation to adopt the new uniform standarisation requirements, within a stipulated time-frame. The South African code developers, after a thorough investigation process which will be highlighted in the paper, decided voluntarily to adopt the Eurocode as the primary model document.
This article considers designing of a renewable electrical power generation system for self-contained homes away from conventional grids. A model based on a technique for the analysis and evaluation of two solar and wind energy sources, electrochemical storage and charging of a housing area is introduced into a simulation and calculation program that aims to decide, based on the optimized results, on electrical energy production system coupled or separated from the two sources mentioned above that must be able to ensure a continuous energy balance at any time of the day. Such system is the most cost-effective among the systems found. The wind system adopted in the study is of the low starting speed that meets the criteria of low winds in the selected region under study unlike the adequate solar resource, which will lead to an examination of its feasibility and profitability to compensate for the inactivity of photovoltaic panels in periods of no sunlight. That is a system with fewer photovoltaic panels and storage batteries whereby these should return a full day of autonomy. Two configurations are selected and discussed. The first is composed of photovoltaic panels and storage batteries and the other includes the addition of a wind system in combination with the photovoltaic system with storage but at a higher investment cost than the first. Consequently, this result proves that is preferable to opt for a purely photovoltaic system supported by the storage in this type of site and invalidates the interest of adding micro wind turbines adapted to sites with low wind resources.
By means of small wind turbines, it is possible to create distributed sources of electricity useful in areas with good wind conditions. Sometimes, however, it is possible to use small wind turbines also in areas characterized by lower average wind speeds during the year. At the small wind turbine design stage, various types of technical solutions to increase the speed of the wind stream, as well as to optimally orientate it, can be applied. The methods for increasing the efficiency of wind energy conversion into electricity in the case of a wind turbine include: the use of a diffuser shielding the turbine rotor and the optimization of blades mounted on the turbine rotor. In the paper, the influence of the diffuser and rotor blades geometry on the efficiency of an exemplary wind turbine for exploitation in the West Pomeranian Province is investigated. The analyses are performed for three types of the diffuser and for three types of rotor blades. Based on them, the most optimal shapes of the diffuser and blades are selected due to the efficiency of the wind turbine. For the turbine with the designed diffuser, calculations of the output power for the assumed different values of the average annual wind speed and the constant Betz power factor and the specified generator efficiency are made. In all the analyzed cases, the amount of energy that can be generated by the turbine during the year is also estimated. Important practical conclusions are formulated on the basis of these calculations. In the final part of the paper, a 3D model of the wind turbine with the diffuser and rotor blades chosen based on earlier analyses is presented. As a material for the diffuser and rotor blades, glass fiber type A is applied. By means of calculations using the finite element method, the limit displacement of the turbine structure under the influence of a hurricane wind are determined. Based on these calculations, the correctness of the modelled small wind turbine structure has been demonstrated.
Traps to catch microfauna transported by wind were installed on already colonised by plants area, in the vicinity of the glacier. After 6-week-exposition 859 individuals of microfauna were caught, of which Nematoda constituted 71%, Tardigrada 22% and Rotifcra 7%. Number of microfauna individuals caught depended on distance from the already colonised areas and presence of plant parts, together with which animals can be transported more easily. Microfauna connected with vegetation, which is transferred together with plant parts, was transported in higher numbers. Probably these taxa (i.e. Diphascon within tardigrades and Dorylaimidae within nematodes) colonise new habitats at first, but other species dominate later in freshwater bodies.
A questionnaire inquiry on response to wind turbine noise was carried out on 361 subjects living in the vicinity of 8 wind farms. Current mental health status of respondents was assessed using Goldberg General Health Questionnaire GHQ-12. For areas where respondents lived, A-weighted sound pressure levels (SPLs) were calculated as the sum of the contributions from the wind power plants in the specific area. Generally, 33.0% of respondents were annoyed outdoors by wind turbine noise at the calculated A-weighted SPL of 31-50 dB, while indoors the noise was annoying to 21.3% of them. The proportion of subjects evaluating the noise produced by operative wind turbines as annoying decreased with increasing the distance from the nearest wind turbine (27.6% at the distance of 400-800 m vs 14.3% at the distance above 800 m, p < 0.016). On the other hand, the higher was the noise level, the greater was the percentage of annoyed respondents (14.0% at SPL up to 40 dB vs 28.1% at SPL of 40-45 dB, p < 0.016). Besides noise and distance categories, subjective factors, such as general attitude to wind turbines, sensitivity to landscape littering and current mental health status, were found to have significant impact on the perceived annoyance. About 50% of variance in annoyance rating might be explained by the aforesaid subjective factors.
The article presents the consequences of the introduction of EU regulation 2016/631 for power park modules (PPMs), of which wind farms are a typical example. Analysing the yearlong course of changes in the generated power, the possibility of a typical wind farm meeting the requirements for the production and absorption of reactive power was checked. It was shown that in the selected cases it was necessary to introduce additional sources of reactive power on the side of the farm’s MV.
Obervations of wind directions and air temperatures in Hornsund, Spitsbergen, in 1978—1985 were used to compute frequency distribution of wind directions and mean air temperatures at particular wind directions. Prevailing easterly winds (60°, 90° and 120°) resulted in lower air temperatures (to —2.2°C) than winter and spring means and in higher (nearly 1°C) than summer and autumn mean temperatures. Greatest positive deviations from mean seasonal temperatures are observed in winter at southerly and southwesterly winds and reach 10°C. Greatest negative deviations from mean seasonal temperatures are noted at northerly winds (330° and 360°) in autumn and reach —3.7°C.
Increasing the share of energy production from renewable sources (RES) plays a key role in the sustainable and more competitive development of the energy sector. Among the renewable energy sources, the greatest increase can be observed in the case of solar and wind power generation. It should be noted that RES are an increasingly important elements of the power systems and that their share in energy production will continue to rise. On the other hand the development of variable generation sources (wind and solar energy) poses a serious challenge for power systems as operators of unconventional power plants are unable to provide information about the forecasted production level and the energy generated in a given period is sometimes higher than the demand for energy in all of the power systems. Therefore, with the development of RES, a considerable amount of the generated energy is wasted. The solution is energy storage, which makes it possible to improve the management of power systems. The objective of this article is to present the concept of electricity storage in the form of the chemical energy of hydrogen (Power to Gas) in order to improve the functioning of the power system in Poland. The expected growth in the installed capacity of wind power plants will result in more periods in which excess energy will be produced. In order to avoid wasting large amounts of energy, the introduction of storage systems is necessary. An analysis of the development of wind power plants demonstrates that the Power to Gas concept can be developed in Poland, as indicated by the estimated installed capacity and the potential amount of energy to be generated. In view of the above, the excess electricity will be available for storage in the form of chemical energy of hydrogen, which
The aim of this paper is to answer the question: Are the Łódź Hills useful for electrical energy production from wind energy or not? Due to access to short-term data related to wind measurements (the period of 2008 and 2009) from a local meteorological station, the measure – correlate – predict approach have been applied. Long-term (1979‒2016) reference data were obtained from ECWMF ERA-40 Reanalysis. Artificial neural networks were used to calculate predicted wind speed. The obtained average wind speed and wind power density was 4.21 ms⁻¹ and 70 Wm⁻¹, respectively, at 10 m above ground level (5.51 ms⁻¹, 170 Wm⁻¹ at 50 m). From the point of view of Polish wind conditions, Łódź Hills may be considered useful for wind power engineering.
This work analyzes the process of construction and manufacturing of a blade used in a wind turbine. The calculation scheme is presented for forces generated on the blade of a wind turbine and parameters are determined of weather conditions in which the designed element would be working. Subsequently, for the chosen aerodynamic profile the characteristics are calculated of its aerodynamic coefficients, which enables the establishing of the angle of attack which impacts the yield of wind engines. The presented process is an introduction to 3D modelling of a wind turbine’s blade and simulation of its creation in a CAM environment.
The paper aimed to get the analysis of spatial horizontal distribution of summer phyto-plankton in a small and shallow lake (Głębokie, Western Polesie, CE Poland) in relation to wind conditions occurring during the research period. The study was conducted in 2011 from 5th of July to 5th of September with eight sampling dates between. Water was sampled in the littoral zone from the depth of 0.5 m in four sites situated in different and opposite to one another lake shores. We analyzed the phytoplankton abundance by the way of chlorophyll a determination as well as the community taxonomic structure. Our research revealed that: a) the direction of the wind, which occurred during sampling might have an important role in the horizontal distribution of planktonic algal biomass within the lake; b) the geomorphology of lake surroundings probably mitigated the influence of wind on phytoplankton distribution; c) even weak or mild wind may influence phytoplankton horizontal differentiation.
The objective of this paper is to present a probabilistic method of analyzing the combinations of snow and wind loads using meteorological data and to determine their combination factors. Calculations are based on data measured at twelve Polish meteorological stations operated by the Institute for Meteorology and Water Management. Data provided are from the years 1966 - 2010. Five combinations of snow load and 10-minute mean wind velocity pressure have been considered. Gumbel probability distribution has been used to fit the empirical distributions of the data. As a result, the interdependence between wind velocity pressure and snow load on the ground for a return period of 50 years has been provided, and the values of the combination factors for snow loads and wind actions are proposed.
In the summer 1980-1981, in the Antarctic areas, in the coastal zone of Admiralty Bay (King George Island), complex measurements were carried out in order to investigate the proportion of wind gustiness in the processes generating marine spray systems and stimulating aerosol mass exchange between the sea and the atmosphere.
The investigations carried out during the 5th Antarctic Expedition of the Polish Academy of Sciences allowed to collect the data concerning specificity of the dynamics of sea-salt nuclei dispersed in the Antarctica region. At the established measuring point measurements at three levels were carried out, basing on which the required profile of the wind characteristics at different heights a.s.l. were obtained.
The frequency of wind occurrence at sectors each 30° as well as mean air temperature at particular wind direction were accounted for the warmest and the coldest year of the investigation period 1978—1987 at Polish Antarctic „Arctowski" Station. The effect of orography on wind direction and air temperature was determined. A great rate of dependence of air temperature and wind direction upon atmospheric circulation type was found. High air temperature at the winds from 300° and 330° directions is related both to the kind of air mass and foehn phenomena.
Observations from 1978—81, 1983 and 1985 collected at the Polish Polar Arctowski Station (King George Island, South Shetland Islands) were used to calculate frequencies of wind directions in 30° sectors and mean air temperatures observed at each wind direction. Results reveal that all over the year the warmest air masses flow onto the South Shetland Islands from the northwest while the coolest ones from the southeast and east.
“Domani è un altro giorno” (Tomorrow is another day): the translation of “Via col vento” (Gone With the Wind) as an idiomatic channel – Gone With the Wind has contributed to the planet’s collective memory, not only because a great percentage of the world’s population has identified with the characters and the stories within, but also because, on a linguistic level, the novel has set in motion considerable reuse phenomena. One wonders how much and in what way the phraseology within the text has influenced contemporary Italian and how translators have approached the original text when preparing the Italian editions of the novel.
The article presents selected issues from the Polish Energy Policy draft until 2040. From many issues, the authors chose the ones they considered the most revolutionary. Firstly, the National Power System should be restructured to meet the challenges of a changing environment, be adapted to the growing demand for electricity, and at the same time have the least impact on the natural environment. These goals can be achieved through reforms to reduce the importance of coal in the energy mix and the development of renewable energy sources, especially offshore wind energy. The next tasks are the development of electromobility, enabling the reduction of pollution caused by transport, and, in the longer term, after 2030, the development of nuclear energy in place of the withdrawn coal power.
The thermal, anemometric and bioclimatic conditions on the topoclimatic scale were investigated in the summer season in the EbbaValley region in central Spitsbergen. Eight measurement sites, representing different ecosystems and different types of active surfaces typical of Spitsbergen, were chosen and automatic, hourly recorded, measurements were per− formed at the sites between 11 and 25 of July 2009. The analysis of the spatial distribution of the air temperature and thewind−chill temperature, both for the dayswith radiation and non−ra− diation weather, indicates that the most favorable regions in the interior of Spitsbergen are those situated in the shielded central parts of the valleys and in the lower parts of the slopes with southern exposure. The thermal and wind conditions are definitely less favorable at the tops of elevations and on the glacier. Large differences between the air temperature and the wind−chill temperature were noted, particularly during the unfavorable non−radiation weather, on the glacier and on open peaks due to a large horizontal and vertical wind−chill temperature gradient. The thermal inversions observed in the Ebba Valley in July 2009 were not of the typi− cal, glacier katabatic wind origin. They appeared during the western air circulation, which brings advection of cooled air from above the cold waters of Petunia Bay. The cold air pene− trates into the valley and pushes upwards themass of warmer air in the valley, creating a rather thin inversion layer, whose upper edge is marked with thin Stratus clouds.