Peat soils (FAO — Gelic Histosols) in the southern Bellsund coast area occur on slopes and terraces. They are formed in places favourable for plant growth, i.e. adequately moistened and fertilized largely with bird excrements. These formations belong to moss peats which are generally decomposed weakly and moderately to about 0.5 m depth. Their content of organic matter is equal to about 30-90%, but it is higher in terrace peats. The latter are more acidified than slope peats. The reaction both of slope and terrace peat soils is as a rule, slightly acid or neutral, and CaC03 content does not exceed 10%. As regards the content of macroelements, that of Al is the highest followed by Ca, Fe, Mg and P. Little K and Ti, and only traces of Na are found. Microelements occur in the following sequence: Mn, Zn, Cu, Cr, Ni, Pb, Co, Cd. Particularly Mn, Zn as well as Cu and Cd were found in a higher concentration. Slope peat soils are richer in macro- and microelements than terrace ones, e.g. 4 times in the case of Mg. Peat soils poor in ash parts (up to 25% ash), contain the fewest elements. Some regularities concern also a vertical distribution of the particular profiles but only with regard to terrace peat soils.
The paper presents characterisation of the eco-chemical condition and potential threats to soils of goose farms on the basis of recent monitoring of a 15-year measuring cycle. It was demonstrated that the observed soil enzymatic inactivation progressing with years of investigations on the examined farms was significantly associated with a very high content of mineral nitrogen and available forms of phosphorus. A distinct tendency towards increased content of heavy metals in soils derived from these farms as well as in their direct neighbourhood observed with the passage of time poses a serious hazard to the environment
The aim of the studies was to evaluate the influence of sowing rate, foliar fertilization (Basfoliar fertilizer 6-12-6) and chemical composition on the mechanical properties of narrow- leaved lupine seeds of cultivars Bojar and Regent. Single seeds were burdened in the direction perpendicular to the parting plane of cotyledons with constant speed 10 mm∙min-1. The crop year and cultivar have significantly differentiated the value of all the analyzed strength parameters of narrow-leaved lupine seeds. The seeds of cultivar Bojar had significantly higher values of all the strength parameters. The designated strength parameters of lupine seeds were negatively correlated with ash content, fiber and protein except for the destructive force. They were also positively correlated with the fat content.
Studies on biocompatibility of AISI 316LVM steel indicate the need to eliminate the nickel from the surface and replace it with other elements of improved biocompatibility. Therefore, in the presented work selected physicochemical and mechanical properties of the diffusive nitrocarburized layer formed by plasma potential by means of an active screen made of the Fe-Cr-Ni were studied. In the paper we present results of microstructure and phase composition of the layers, roughness, and surface wettability, potentiodynamic pitting corrosion resistance, penetration of ions into the solution as well as mechanical properties. The studies were conducted for the samples of both mechanically polished and nitrocarburized surfaces, after sterilization, and exposure to the Ringer’s solution. Deposition of the nitrocarburized layer increased the contact angle, surface roughness, surface hardness, and corrosion resistance with respect to the polished surfaces. The nitrocarburized layer is a barrier against the ions release into the solution and sterilization and exposure to Ringer solution. The obtained results showed beneficial increase of both mechanical and electrochemical properties of the deposited layer, and thus the applicability of the proposed method of surface treatment of the 316LVM steel for short-term implants after sterylization.
The paper presents the influence of different liquid cargo properties on discharge rate of hydraulic submerged cargo pumps on modern product and chemical tankers is presented in the paper. Main parts of submerged cargo pumps and hydraulic drive system are described. Some examples of technical solutions of the described systems installed on board of the newly building constructed ship m/t ‘Helix’ are presented. The formula of use application of flow and drive characteristics of cargo pumps is given. These characteristics were made derived for a basic cargo (fresh water) for the case of the service of a real cargo of different viscosity and density.
Along with the increase in popularity of the sewage sludge thermal treatment methods in Poland resulting from the implementation of European Union law, a management problem with ash, which is produced as a result of this process, appeared. The paper analyses the chemical composition and physical properties of fl y ash from thermal treatment of municipal sewage sludge in terms of its use in concrete technologies in relation to EN 450-1 Fly ash for concrete. Defi nition, specifi cations and conformity criteria (2012) and EN 197-1 Cement. Composition, specifi cations and conformity criteria for common cements (2011) standards. The tested material did not meet the requirements related to use of fl y ash for concrete production (chemical composition, low activity index, high water demand and fi neness), and as main and minor components for cement production. On the basis of the carried out research and analyses, it was found that the hardening slurry technology creates the greatest possibilities related to the management of fl y ash from thermal treatment of municipal sewage sludge.