Nauki Techniczne

Archives of Civil Engineering

Zawartość

Archives of Civil Engineering | 2015 | No 2

Abstrakt

In order to identify the modal parameters of civil structures it is vital to distinguish the defective data from that of appropriate and accurate data. The defects in data may be due to various reasons like defects in the data collection, malfunctioning of sensors, etc. For this purpose Exploratory Data Analysis (EDA) was engaged toenvisage the distribution of sensor’s data and to detect the malfunctioning with in the sensors. Then outlier analysis was performed to remove those data points which may disrupt the accurate data analysis. Then Data Driven Stochastic Sub-space Identification (DATA-SSI) was engaged to perform the modal parameter identification. In the end to validate the accuracy of the proposed method stabilization diagrams were plotted. Sutong Bridge, one of the largest span cable stayed bridge was used as a case study and the suggested technique was employed. The results obtained after employing the above mentioned techniques are very valuable, accurate and effective.

Przejdź do artykułu

Autorzy i Afiliacje

I. Khan
D. Shan
Q. Li

Abstrakt

During implementation of construction projects, durations of activities are affected by various factors. Because of this, both during the planning phase of the project as well as the construction phase, managers try to estimate, or predict, the length of any delays that may occur. Such estimates allow for the ability to take appropriate action in terms of planning and management during the execution of construction works. This paper presents the use of the non-deterministic concept for describing the uncertainty of estimating works duration. The concept uses the theory of fuzzy sets. The author describes a method for fuzzy estimations of construction works duration based on the fact that uncertain data is an inherent factor in the conditions of construction projects. An example application of the method is presented. The author shows a fuzzy estimation for the duration of an activity, taking into consideration the distorting influence caused by malfunctioning construction equipment and delivery delays of construction materials.

Przejdź do artykułu

Autorzy i Afiliacje

N. Ibadov

Abstrakt

To investigate the mechanical properties of tunnel lining concrete under different moderate-low strain rates after high temperatures, uniaxial compression tests in association with ultrasonic tests were performed. Test results show that the ultrasonic wave velocity and mass loss of concrete specimen begin to sharply drop after high temperatures of 600°C and 400°C, respectively, at the strain rates of 10‒5s‒1 to 10‒2s‒1. The compressive strength and elastic modulus of specimen increase with increasing strain rate after the same temperature, but it is difficult to obtain an evident change law of peak strain with increasing strain rate. The compressive strength of concrete specimen decreases first, and then increases, but decreases again in the temperatures ranging from room temperature to 800°C at the strain rates of 10‒5s‒1 to 10‒2s‒1. It can be observed that the strain-rate sensitivity of compressive strength of specimen increases with increasing temperature. In addition, the peak strain also increases but the elastic modulus decreases substantially with increasing temperature under the same strain rate.

Przejdź do artykułu

Autorzy i Afiliacje

L.X. Xiong

Abstrakt

Light-weight Self-Compacting Concrete (LWSCC) might be the answer to the increasing construction requirements of slenderer and more heavily reinforced structural elements. However there are limited studies to prove its ability in real construction projects. In conjunction with the traditional methods, artificial intelligent based modeling methods have been applied to simulate the non-linear and complex behavior of concrete in the recent years. Twenty one laboratory experimental investigations on the mechanical properties of LWSCC; published in recent 12 years have been analyzed in this study. The collected information is used to investigate the relationship between compressive strength, elasticity modulus and splitting tensile strength in LWSCC. Analytically proposed model in ANFIS is verified by multi factor linear regression analysis. Comparing the estimated results, ANFIS analysis gives more compatible results and is preferred to estimate the properties of LWSCC.

Przejdź do artykułu

Autorzy i Afiliacje

B. Vakhshouri
S. Nejadi

Abstrakt

One of the main threats to constructions made from rammed earth is destruction due to exposure to water. The way to limit this dangerous phenomenon is to supplement the local soil mixtures with stabilizing agents. The main component used is Portland cement. This article analyses the results of research which focused on the resistance of rammed earth to water erosion. Because of the lack of national standards regarding the method of examining the durability of rammed earth, the research was based on the New Zealand standard NZS 4298: 1998. The results confirm the possibility of using rammed earth stabilized by cement in a temperate climate.

Przejdź do artykułu

Autorzy i Afiliacje

P.L. Narloch
P. Woyciechowski
E. Dmowska
K. Halemba

Abstrakt

The subject of the numerical investigation is an ellipsoidal head with a central (axis-symmetrical) nozzle. The nozzle is loaded by axial load force. The ellipsoidal head is under axial-symmetrical compression load. The numerical FEM model is elaborated. The calculation will provide the critical loads and equilibrium paths for the sample head.. The investigation will measure the influence of the diameter of the nozzle on the critical state of the ellipsoidal head.

Przejdź do artykułu

Autorzy i Afiliacje

P. Jasion
K. Magnucki

Abstrakt

Probabilistic analysis of a space truss is presented in the paper. Reliability of such a structure is sensitive to geometrical and material imperfections. The objective of this paper is to present a variant of the point estimate method (PEM) to determine mean values and standard deviations of limit loads of engineering structures. The main advantage presented by this method is the small number of sample calculations required to obtain estimators of investigated parameters. Thus the method is straightforward, requiring only preliminaries of probability theory. This approach is illustrated by limit state analysis of a space truss, considering geometric and material imperfections. The calculations were performed for different random models, so the influence of random parameters on the limit load of the truss can be determined. A realistic snow load was imposed.

Przejdź do artykułu

Autorzy i Afiliacje

P. Sorn
J. Górski
J. Przewłócki

Abstrakt

The paper presents findings from research project Mobis which is aimed at developing a method of assessing safety of unsignalised pedestrian road crossings using video image analysis. Pedestrian and vehicle traffic has been recorded at selected zebra crossing sites in Warsaw and Wrocław, before and after installation of active signage systems SignFlash and Levelite. Speeds of approaching vehicles were measured and drivers’ behaviour was classified using video analysis.

The paper presents a comparison of effectiveness of systems such as SignFlash and Levelite based on changes in the mean and standard deviation of vehicle spot speeds as well as changes in speed profiles of vehicles approaching the crossings.

Results indicate that both SignFlash and Levelite active signage reduce mean vehicle approach speeds and have a positive impact on drivers’ behaviour.

Przejdź do artykułu

Autorzy i Afiliacje

P. Olszewski
W. Czajewski
P. Dąbkowski
C. Kraśkiewicz
P. Szagała

Abstrakt

One of the basic parameters which describes road traffic is Annual Average Daily Traffic (AADT). Its accurate determination is possible only on the basis of data from the continuous measurement of traffic. However, such data for most road sections is unavailable, so AADT must be determined on the basis of short periods of random measurements. This article presents different methods of estimating AADT on the basis of daily traffic (VOL), and includes the traditional Factor Approach, developed Regression Models and Artificial Neural Network models. As explanatory variables, quantitative variables (VOL and the share of heavy vehicles) as well as qualitative variables (day of the week, month, level of AADT, the cross-section, road class, nature of the area, spatial linking, region of Poland and the nature of traffic patterns) were used. Based on comparisons of the presented methods, the Factor Approach was identified as the most useful.

Przejdź do artykułu

Autorzy i Afiliacje

M. Spławińska

Abstrakt

In this stud y, we attempt to analyse free nonlinear vibrations of buckling in laminated composite beams. Two new methods are applied to obtain the analytical solution of the nonlinear governing equation of the problem. The effects of different parameters on the ratio of nonlinear to linear natural frequencies of the beams are studied. These methods give us an agreement with numerical results for the whole range of the oscillation amplitude.

Przejdź do artykułu

Autorzy i Afiliacje

G. Abdollahzadeh
M. Ahmadi

Zasady etyki publikacyjnej

ETHICS POLICY

”Archives of Civil Engineering” respects and promotes the principles of publishing ethics. Being guided by COPE’s Guidelines ( https://publicationethics.org/resources/guidelines) we ensure that all participants of the publishing process comply with these rules, the journal pays special attention to:

Editor Responsibilities
1. Qualifying individual manuscripts for publication only on the basis of: (a) compliance with the guidelines provided to the authors, (b) substantive value, (c) originality, (d) transparency of presentation
2. Deciding whether the paper fulfills all requirements i.e. formal and scientific and which articles submitted to the journal should be published. In making these decisions, the editor may be guided by the policies of the journal’s editorial board as well as by legal requirements regarding libel, copyright infringement, and plagiarism.
3. Evaluating manuscripts for intellectual content without regard to race, gender, sexual orientation, religious belief, ethnic origin, citizenship, or political philosophy of the author(s).
4. Ensuring scientific accuracy and complying with the principle of authorship; making sure that individual authors who contribute to the publication accept its form after the scientific editing
5. Providing a fair and appropriate peer review process.
6. Withdrawing manuscripts from publication, if any information about its unreliability appeared, also as a result of unintentional errors, features of plagiarism or violation of the rules of publishing ethics were identified.
7. Requiring all contributors to disclose relevant competing interests and publish corrections if competing interests are revealed after publication. If needed, other appropriate action should be taken, such as the publication of a retraction or expression of concern.
8. Maintaining the integrity of the academic record, precludes business needs from compromising intellectual and ethical standards, and is always willing to publish corrections, clarifications, retractions, and apologies when needed.
9. Not disclosing any information about a manuscript under consideration to anyone other than the author(s), reviewers and potential reviewers, and in some instances the editorial board members, as appropriate.

Reviewer Responsibilities
1. Cooperating with the scientific editor and / or editorial office and the authors in the field of improving the reviewed material;
2. Being objective and expressing the views clearly with appropriate supporting arguments.
3. Assessing of the entrusted works in a careful and objective manner, if possible with an assessment of their scientific reliability and with appropriate justification of the comments submitted;
4. identifying relevant published work that has not been cited by the authors
5. calling to the editor's attention any substantial similarity or overlap between the manuscript under consideration and any other published data of which they have personal knowledge
6. Maintaining the principle of fair play, excluding personal criticism of the author (s)
7. Maintaining confidentiality, which is not showing or discussing with others except those authorized by the editor. Any manuscripts received for review are treated as confidential documents.
8. Performing a review within the set time limit or accepting another solution jointly with ACE in the event of failure to meet this deadline.
9. Notifying the editor if the invited reviewer feels unqualified to review the manuscript or knows that its timely review will be impossible.
10. identifying relevant published work that has not been cited by the authors
11. Not considering evaluating manuscripts in which they have conflicts of interest resulting from competitive, collaborative, or other relationships or connections with any of the authors, companies, or institutions connected to the submission.

Author Responsibilities
1. Results of original research should present an accurate account of the work performed as well as an objective discussion of its significance. Underlying data should be represented accurately in the manuscript. A paper should contain sufficient detail and references to permit others to replicate the work. Fraudulent or knowingly inaccurate statements constitute unethical behaviour and are unacceptable.
2. The authors should follow the principle of originality, which is submitting only their own original works, and in the case of using the works of other authors, marking them in accordance with the rules of quotation, or obtaining consent for the publication of previously published materials from their owners or administrators;
3. An author should not in general publish manuscripts describing essentially the same research in more than one journal or primary publication. Parallel submission of the same manuscript to more than one journal constitutes unethical publishing behaviour and is unacceptable.
4. Authorship should be limited to those who have made a significant contribution to the conception, design, execution, or interpretation of the reported study and phenomena such as ghostwriting or guest authorship in the event of their detection must be actively counteracted.
5. All authors should report in a Reliable manner the sources they used to create their own study and their inclusion in the attachment bibliography;
6. All those who have made significant contributions should be listed as co-authors. Where there are others who have participated in certain substantive aspects of the research project, they should be named in an Acknowledgement section.
7. The corresponding author should ensure that all appropriate co-authors (according to the above definition) and no inappropriate co-authors are included in the author list of the manuscript, and that all co-authors have seen and approved the final version of the paper and have agreed to its submission for publication.
8. All authors should disclose in their manuscript any financial or other substantive conflict of interest that might be construed to influence the results or their interpretation in the manuscript. All sources of financial support for the project should be disclosed.
9. When an author discovers a significant error or inaccuracy in his/her own published work, it is the author’s obligation to promptly notify the journal’s editor or publisher and cooperate with them to either retract the paper or to publish an appropriate erratum.

Publisher’s Confirmation
In cases of alleged or proven scientific misconduct, fraudulent publication or plagiarism the publisher, in close collaboration with the editors, will take all appropriate measures to clarify the situation and to amend the article in question. This includes the prompt publication of an erratum or, in the most severe cases, the complete retraction of the affected work.

Procedura recenzowania

Manuscript Peer-Review Procedure

”Archives of Civil Engineering” makes sure to provide transparent policies for peer-review, and reviewers have an obligation to conduct reviews in an ethical and accountable manner. There is clear communication between the journal and the reviewers which facilitates consistent, fair, and timely review.

-The model of peer-review is double-blind: the reviewers do not know the names of the authors, and the authors do not know who reviewed their manuscript (but if the research is published reviewers can eventually know the names of the authors). A complete list of reviewers is published in a traditional version of the journal: in-print.
-It is the editor who appoints two reviewers; however, if there are discrepancies in the assessment the third reviewer can be appointed.
-After having accepted to review the manuscript (one-week deadline), the reviewers have approximately 6 weeks to finish the process.
-The paper is published in ACE provided that the reviews are positive. All manuscripts receive grades from 1-5, 5 being positive, 1 negative, the authors receive reviews to read and consider the comments.
-Manuscript evaluations are assigned one of five outcomes: accept without changes, accept after changes suggested by the reviewer, rate manuscript once again after major changes and another review, reject, withdraw.
-Manuscripts requiring minor revision (accept after changes suggested by the reviewer) does not require a second review. All manuscripts receiving a "Rate manuscript once again after major changes and another review " evaluation must be subjected to a second review. Rejected manuscripts are given no further consideration. There are cases when the article can be withdrawn, often upon the request of an author, technical reason (e.g. names of authors are placed in the text, lack of references, or inappropriate structure of the text), or plagiarism.
-The revised version of the manuscript should be uploaded to the Editorial System within six weeks. If the author(s) failed to make satisfactory changes, the manuscript is rejected.
-On acceptance, manuscripts are subject to editorial amendment to suit house style.
-Paper publication requires the author's final approval.
- As soon as the publication appears in print and in electronic forms on the Internet there is no possibility to change the content of the article.

Editor’s responsibilities
-The editor decides whether the paper fulfills all requirements i.e. formal and scientific and which articles submitted to the journal should be published.
-In making these decisions, the editor may be guided by the policies of the journal’s editorial board as well as by legal requirements regarding libel, copyright infringement, and plagiarism.
-The editor maintains the integrity of the academic record, precludes business needs from compromising intellectual and ethical standards, and is always willing to publish corrections, clarifications, retractions, and apologies when needed.
-The editor evaluates manuscripts for intellectual content without regard to race, gender, sexual orientation, religious belief, ethnic origin, citizenship, or political philosophy of the author(s).
-The editor does not disclose any information about a manuscript under consideration to anyone other than the author(s), reviewers and potential reviewers, and in some instances the editorial board members, as appropriate.

Reviewers' responsibilities
Any manuscripts received for review are treated as confidential documents. They must not be shown to or discussed with others except if authorized by the editor. Privileged information or ideas obtained through peer review is kept confidential and not used for personal advantage Any invited reviewer who feels unqualified to review the manuscript or knows that its timely review will be impossible should immediately notify the editor so that alternative reviewers can be contacted. Reviewers should identify relevant published work that has not been cited by the authors. Any statement that an observation, derivation, or argument had been previously reported should be accompanied by the relevant citation. A reviewer should also call to the editor's attention any substantial similarity or overlap between the manuscript under consideration and any other published data of which they have personal knowledge. Reviewers should not consider evaluating manuscripts in which they have conflicts of interest resulting from competitive, collaborative, or other relationships or connections with any of the authors, companies, or institutions connected to the submission. Reviews should be conducted objectively. Personal criticism of the author is unacceptable. Referees should express their views clearly with appropriate supporting arguments. All reviews must be carried out on a special form available in the Editorial System.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji